INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET – BRYAN, OHIO 43506
(800) 495-0276 FAX (800) 892-6276 © 2012 CCN 46750519
www.ingersollrandproducts.com
OPERATOR’S MANUALPH15F-XXX-XXX-X
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE RELEASED: 12-14-12
(REV. A)

1.5" DIAPHRAGM PUMP

2:1 RATIO (METALLIC)

READ THIS MANUAL CAREFULLY BEFORE INSTALLING,

OPERATING OR SERVICING THIS EQUIPMENT.

It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
Figure 1

SERVICE KITS

Refer to Model Description Chart to match the pump mate-
rial options.
637445-XX for Fluid section repair (see page 4). NOTE: This kit
also contains several air motor seals which will need to be
replaced.
637389 for Air Motor Service Kit (see page 6).
637390-7 for Major Air Valve Kit (see page 7).

PUMP DATA

Models .. . . . . . . . . . see Model Description Chart for “-XXX”
Pump Type . . . . . . . Metallic Air Operated Double Diaphragm
Material .. . . . . . . . . see Model Description Chart
Weight ............................. 88 lbs (39.9 kgs)
Maximum Air Inlet Pressure . . . . . . . 100 p.s.i.g. (6.9 bar)
Maximum Material Inlet Pressure . . 10 p.s.i.g. (0.69 bar)
Maximum Outlet Pressure .. . . . . . . . 200 p.s.i.g. (13.8 bar)
Maximum Flow Rate . . . . . . . . . . . . . . . 63 g.p.m. (238.5 p.m.)
Displacement / Cycle @ 100 p.s.i.g. 0.88 gal. (3.33 lit.)
Maximum Particle Size . . . . . . . . . . . . 1/4” dia. (6.4 mm)
Maximum Temperature Limits (diaphragm / ball / seal
material)
E.P.R. / EPDM .. . . . . . . . . . . . . -60° to 280° F (-51° to 138° C)
Hytrel® . . . . . . . . . . . . . . . . . . . -20° to 150° F (-29° to 66° C)
Polypropylene .. . . . . . . . . . . 35° to 175° F (2° to 79° C )
Santoprene® .. . . . . . . . . . . . . -40° to 225° F (-40° to 107° C)
PTFE. . . . . . . . . . . . . . . . . . . . . . 40° to 225° F (4° to 107° C)
Viton® . . . . . . . . . . . . . . . . . . . . -40° to 350° F (-40° to 177° C)
Dimensional Data .................. see page 8
Noise Level @ 70 p.s.i., 54 c.p.m.
. . 75.6 db(A)
Tested with 350-568 muer assembly installed.
The pump sound pressure levels published here have been updated to
an Equivalent Continuous Sound Level (L
Aeq
) to meet the intent of ANSI
S1.13-1971, CAGI-PNEUROP S5.1 using four microphone locations.
NOTICE: All possible options are shown in the chart, however, certain
combinations may not be recommended, consult a representative or
the factory if you have questions concerning availability.

MODEL DESCRIPTION CHART

PH15 F - X S P - S X X - X
Air Motor / Air Cap Material
F - Conduc tive Polypropylene
/ Stainless Steel
Fluid Connection
A - 1 1/2 N.P.T.F.
B - 1 1/2 BSP parallel
F - 1 1/2 ANSI / DIN Flange
Ball Material
A - Santoprene T - PTFE
C - Hytrel V - Viton
Fluid Section Service Kit Selection
EXAMPLE: Model #PH15F-ASP-SAA-C
Fluid Section Service Kit # 637445-XX
PH15F - XXX - X X X - X
Ball Diaphragm
637445 - X X
Fluid Cap & Manifold Material
S - Stainless Steel
Diaphragm Material
A - Santoprene T - PTFE / Santoprene
C - Hytrel
Seat Material
S - Stainless Steel
Hardware Material
P - Plated Steel
Pump Size
15 - 1.5”