Ingersoll-Rand PH30F-XXX-XXX-C manual Ratio Metallic, Service Kits, Pump Data

OPERATOR’S MANUAL	PH30F-XXX-XXX-C
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE	RELEASED: 5-28-08
	REVISED: 11-13-10

3" DIAPHRAGM PUMP

2:1 RATIO (METALLIC)

(REV. 04)

READ THIS MANUAL CAREFULLY BEFORE INSTALLING,

OPERATING OR SERVICING THIS EQUIPMENT.

It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.

SERVICE KITS

Refer to Model Description Chart to match the pump mate- rial options.

637441-XX for fluid section repair (see page 4). NOTE: This kit also contains several air motor seals which will need to be replaced.

637369 for air section repair (see page 6).

637374-6 major air valve assembly (see page 7).

PUMP DATA

Models. . . . . . . . . . . see Model Description Chart for “-XXX” Pump Type. . . . . . . Metallic Air Operated Double Diaphragm Material. . . . . . . . . . see Model Description Chart

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268 lbs (121.6 kgs) Maximum Air Inlet Pressure . . . . . . . 100 p.s.i.g. (6.9 bar) Maximum Material Inlet Pressure. . 10 p.s.i.g. (0.69 bar) Maximum Outlet Pressure . . . . . . . . . 200 p.s.i.g. (13.8 bar)

Maximum Flow Rate . . . . . . . . . . . . . . . 150 g.p.m. (567.8 l.p.m.) flooded inlet . . . . . . . . . . . 160 g.p.m. (605.6 l.p.m.)

Displacement / Cycle @ 100 p.s.i.g. 1.4 gal. (5.3 lit.) Maximum Particle Size . . . . . . . . . . . . 3/8” dia. (9.5 mm)

Maximum Temperature Limits (diaphragm / ball / seal material)

E.P.R. / EPDM. . . . . . . . . . . . . . -60° to 280° F (-51° to 138° C) Hytrel® . . . . . . . . . . . . . . . . . . . -20° to 150° F (-29° to 66° C) Nitrile . . . . . . . . . . . . . . . . . . . . 10° to 180° F (-12° to 82° C)

Polypropylene . . . . . . . . . . . . 35° to 175° F (2° to 79° C) Santoprene®. . . . . . . . . . . . . . -40° to 225° F (-40° to 107° C) PTFE. . . . . . . . . . . . . . . . . . . . . . 40° to 225° F (4° to 107° C) Viton® . . . . . . . . . . . . . . . . . . . . -40° to 350° F (-40° to 177° C)

Dimensional Data. . . . . . . . . . . . . . . . . . see page 8 Noise Level @ 70 p.s.i., 50 c.p.m.c . . 83.0 db(A)d

cTested with 67263 muffler assembly installed.

dThe pump sound pressure levels published here have been updated to

an Equivalent Continuous Sound Level (LAeq) to meet the intent of ANSI S1.13-1971, CAGI-PNEUROP S5.1 using four microphone locations.

NOTICE: All possible options are shown in the chart, however, certain combinations may not be recommended, consult a representative or the factory if you have questions concerning availability.

INGERSOLL RAND COMPANY LTD

209 NORTH MAIN STREET – BRYAN, OHIO 43506

(800) 276-4658 y FAX (800) 266-7016	© 2010	CCN 15307648
www.ingersollrandproducts.com

Figure 1

MODEL DESCRIPTION CHART

PH30F - X S S - S X X - C

Air Motor / Air Cap Material

F- Conductive Polypropylene

/Stainless Steel

Fluid Connection

A - 3 - 8 N.P.T.F. - 1

B - Rp 3 (3 - 11 BSP parallel)

Fluid Cap & Manifold Material

S - Stainless Steel

Hardware Material

S - Stainless Steel

Seat Material

S - Stainless Steel

Ball Material

A - Santoprene T - PTFE

C - Hytrel V - Viton

Diaphragm Material

A - Santoprene T - PTFE / Santoprene

C - Hytrel

Fluid Section Service Kit Selection	PH30F - ASS - S X X - C
EXAMPLE: Model #PH30F-ASS-SAA-C	637441 - X X
	Ball	Diaphragm
Fluid Section Service Kit # 637441-AA