|
|
|
|
|
|
|
| ||
5 | Press | to select an IP mode. You can select: | 3 Press ENTER. Your player searches for stations | ||||||
| • | with a strong signal and stores the station | |||||||
| information. When the search is complete, your | ||||||||
|
| obtain an IP address. | |||||||
|
| player tunes to the first station it found. | |||||||
| • | ||||||||
|
|
|
| ||||||
|
| network settings, such as IP address, subnet |
|
|
| ||||
|
|
| Note | ||||||
|
| mask, and gateway settings. |
|
| • Your player can store up to 20 radio stations. | ||||
| • |
|
| • If auto installation is not activated or less than 5 | |||||
6 | Press | to go to the previous menu. |
|
| radio stations are stored, you will be prompted | ||||
|
| to install the radio stations again. | |||||||
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
Testing the network configuration’s connectivity
You can test the connectivity of the network configuration by “pinging” an IP address. Pinging means sending a signal to an IP address and waiting for a returning signal.
To test the network configuration’s connectivity:1Press ENTER. The Settings menu opens.
Parental
System
Network | Wired |
| |
Settings |
|
Display | Network Test |
| |
Audio |
|
Language |
|
2Press or to select Network.
3Press , press or to select Network Test, then press ENTER.
Playing files on a portable media player
To play file on a portable media player:1Connect a stereo audio cable from the AUX IN 3 jack on the front of your player to the headphone jack on the media player (such as an MP3 player).
2Press AUDIO SOURCE repeatedly until AUX 3 is displayed.
3Use the controls on the media player to start, stop, and control playback.
Note
•Playback can only be controlled using the controls on the portable media player.
•Stop playback on the portable media player before you switch the input source.
Listening to the radio
To listen to the radio for the first time:1Make sure that you have installed the FM and AM antennas. See “Connecting radio antennas” on page 7.
2Press RADIO. “AUTO INSTALL ... PRESS PLAY” is displayed.
1Press RADIO to switch to radio mode and select the FM or AM radio band.
2Press /PRESET+ or /PRESET– to select a preset radio station.3Press /TUNE– or /TUNE+ to tune to the previous or next radio frequency. Press and hold one of these buttons for two seconds to automatically search for radio stations.
Scanning for stations and storing radio presets
To scan for stations and store radio presets:1Press RADIO.
2Press AUTO SCAN. All the available radio stations with a strong signal will be stored automatically. Your player can store up to 20 stations.
3Press PROGRAM. The first available preset number blinks on the display.
4Press or (or press the number buttons) to select the preset number you want to use.
5Press PROGRAM to confirm.
Maintaining
General guidelines
•The top and back panels of your player may become hot after a long period of use. This is not a malfunction.
•When you are not using your player, make sure that you remove the disc and put your player into standby mode.
•If you do not use your player for a long period of time, it may not function correctly. Turn on and use your player occasionally.
•Do not place objects on the disc tray.
•Do not locate your player:
•Near heating devices or in an enclosed vehicle
•In an area with a temperature over 104°F (40°C) or humidity over 90%
•Dirty places
•In an area with direct exposure to sunlight
•Do not install this equipment in a confined space such as a book case or similar unit. The ventilation should not be impeded by covering the ventilation openings with items such as newspapers,
•Make sure that you leave a minimum of 4 inches (10 cm) around your player for sufficient ventilation.
18 | www.insigniaproducts.com |