Insignia NS-LCD15-09 15.6" LCDTV 720P

Appendix

 

VGA input

D-Sub 15-pin terminal

 

 

 

E-EDID compliant

To attach a wall mount bracket to your TV:

 

Suggested scan rates:640×480 /60 Hz,

 

800×600 /60 Hz, 1024×768 /60 Hz,

1 Remove the four M4 screws holding your TV

 

1440×900 /60 Hz,

to the stand.

 

 

Audio input: Headphone mini-jack for

2 Secure the wall mount bracket to the back of

 

stereo

Dimensions

15.0 × 11.6 × 5.4 inches

your TV using four M4 screws, as indicated in

the illustration.

 

(with base)

(38.1 × 29.4 × 13.7 cm)

 

M4 screws

Weight

6.6 lbs. (3 kg)

75 mm

Accessories

Power cord

 

 

 

 

User guide

 

 

 

Remote control

 

 

 

Batteries (2 AAA)

Attach wall

75 mm

 

VGA cable

 

PC audio cable

bracket here

 

 

 

Quick Start guide

Legal notices

Remove M4 screws

Remove stand

Specifications

Design and specifications are subject to change without notice.

Analog standard

NTSC

 

 

Digital standard

ATSC, 8-VSB, Clear-QAM

 

 

Screen

15.6-inch

 

 

Channel coverage

VHF: 2-13

 

UHF: 14-69

 

CATV: Mid band - A-8 ~ A-1, A ~ I

 

Super band - J ~ W

 

Hyper band - AA ~ ZZ, AAA, BBB

 

Ultra band - 65 ~ 94, 100 ~ 135

 

 

Power source

AC 100~240 V 50/60 Hz

 

 

Power consumption

<60 W

 

<1 W in standby mode

Audio power

2 W + 2 W internal speaker

 

 

S-Video input

Y:1 V(p-p), 75 ohm, negative sync

 

C:0.286 V(p-p) (burst signal), 75 ohm

 

 

Video/audio input

Video:1 V(p-p), 75 ohm, negative sync

 

Audio:500 mV(rms)

Component input

Y:1 V(p-p), 75 ohm, including sync

 

Pr/Cr:±0.35 V(p-p), 75 ohm

 

Pb/Cb:±0.35 V(p-p), 75 ohm

 

Audio:500 mV(rms)

 

Suggested resolutions:1080i, 720p,

 

480p, 480i

 

 

HDMI input

1 HDMI input terminal

 

HDCP compliant

 

E-EDID compliant

 

Suggested scan rates:1080i, 720p, 480p,

 

480i

FCC Part 15

This device complies with Part 15 of the FCC Rules. Operation of this product is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply within the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced technician for help.

FCC warning

Changes or modifications not expressly approved by the party responsible for compliance with the FCC Rules could void the user’s authority to operate this equipment.

Cables

Connections to this device must be made with shielded cables with metallic RF/EMI connector hoods to maintain compliance with FCC Rules and Regulations.

Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

14

www.insignia-products.com