Manuals / Brands / Baby / Crib Toy / Intel / Baby / Crib Toy

Intel D2700 3.2.2.2 Add-in Card Connectors , NOTE

1 113

Download 113 pages, 4.72 Mb

Embedded Intel® Atom™ Processor D2700 with Intel® NM10 Express Chipset Development Kit User‘s Manual

57

3.2.2.2 Add-in Card Connectors

The board has the following add-in card connectors:

 PCI Express Full-/Half-Mini Card slot

 Conventional PCI bus connector (with riser card support for up to two PCI cards)

Note the following considerations for the Conventional PCI bus connector:

 The Conventional PCI bus connector is bus master capable.

 SMBus signals are routed to the Conventional PCI bus connector. This enables

Conventional PCI bus add-in boards with SMBus support to access sensor data on

the board. The specific SMBus signals are as follows:

 The SMBus clock line is connected to pin A40.

 The SMBus data line is connected to pin A41.

The Conventional PCI bus connector also supports single-slot and dual-slot riser cards

for use of up to two bus master PCI expansion cards. In order to support two PCI bus

master expansion cards, the riser card must support the following PCI signal routing:

 Pin A11: additional 33 MHz PCI clock

 Pin B10: additional PCI Request signal (i.e., PREQ#2)

 Pin B14: additional PCI Grant signal (i.e., GNT#2)



NOTE

BIOS IRQ programming for the second PCI slot on PCI riser card:

 ID_SEL: AD20 (Device 4)

 Second PCI slot INT Mapping:

 INT A# (A6)



INT D# of mother board PCI slot.

 INT B# (B7)



INT A# of mother board PCI slot.

 INT C# (A7)



INT B# of mother board PCI slot.

 INT D# (B8)



INT C# of mother board PCI slot.



NOTE

The Conventional PCI slot on this board does not support the PCI PHOLD

1

function. Due

to this limitation (errata), certain PCI cards may experience performance or detection

issues when DMA transfer is used as part of the PCI card operation.

1

PHOLD is the signal required to hold the bus during DMA transfers.

Contents

Main Embedded Intel AtomTM Processor D2700 with Intel NM10 Express Chipset Development Kit Users Manual Revision History Date Revision History Revision Component Information Ordering Information Preface Intended Audience What This Document Contains Typographical Conventions Notes, Cautions, and Warnings Other Common Notations Contents 1 Development Kit Contents ................................................... 12 2 Intel Embedded Board D2700 Overview ............................ 14 3 Technical Reference ............................................................ 43 4 Overview of BIOS Features ................................................. 68 5 Board Status and Error Messages ........................................ 77 6 Assembly/Disassembly Guide ............................................. 84 7 Operating System Reference ............................................... 88 8 Battery Disposal ................................................................ 111 Figures Tables Page 1 Development Kit Contents 1.1 Included Hardware and Documentation 1.2 Development Kit Images 2 Intel Embedded Board D2700 Overview 2.1 Overview 2.1.1 Feature Summary Table 1 summarizes the features of Intel Embedded Board D2700. Table 1. Feature Summary Table 1. Feature Summary (continued) 2.1.2 Board Layout 17 Item/callout from Figure 1 Description 2.1.3 Block Diagram 2.2 Online Support 2.3 Supported Operating Systems 2.4 BIOS vendors 2.5 Processor 2.5.1 Intel Embedded Board D2700 Graphics Subsystem 2.5.1.1 Intel Graphics Media Accelerator 3600 Graphics Controller (Intel GMA) 2.5.1.2 Video Video image Enhancement: Hue, Saturation, Brightness, Contrast (HSBC) adjust, Bob 2.6 System Memory NOTE Page Page 2.7 Intel NM10 Express Chipset 2.7.1 Video Memory Allocation 2.7.2 Analog Display (VGA) 2.7.3 Digital Visual Interface (DVI-I) 2.7.4 Flat Panel Interface (LVDS) 2.7.5 Configuration Modes 2.7.6 USB 2.7.7 SATA Support 2.8 Real-Time Clock Subsystem 2.9 Legacy I/O Controller 2.9.1 Serial Ports 2.9.2 Parallel Port 2.9.3 Keyboard and Mouse Interfaces 2.10 LAN Subsystem 2.10.1 Intel 82574L Gigabit Ethernet Controllers 2.10.2 LAN Subsystem Software and Drivers 2.10.3 RJ-45 LAN Connector with Integrated LEDs 2.11 Audio Subsystem 2.11.1 Audio Subsystem Software 2.11.2 Audio Connectors and Headers 2.12 Hardware Management Subsystem 2.12.1 Hardware Monitoring 2.12.2 Thermal Monitoring 2.13 Power Management 2.13.1 ACPI 37 2.13.1.1 System States and Power States Global States Sleeping States Processor States Device States 2.13.1.2 Wake-up Devices and Events NOTE 2.13.2 Hardware Support NOTE 2.13.2.1 Fan Header 2.13.2.2 LAN Wake Capabilities Page Page 2.14 Debug Interfaces 3 Technical Reference 3.1 Memory Map 3.1.1 Addressable Memory Page Table 10 lists the system memory map. Table 10. System Memory Map 3.2 Connectors and Headers 47 3.2.1 Back Panel Item 3.2.1.1 Back Panel Connectors Figure 9 shows the location of the back panel connectors. 3.2.1.2 I/O Shield Page 50 Item/callout from Figure 11 Description 3.2.2.1 Signal Tables for the Connectors and Headers Table 12. TPM Header Table 13. Serial Port Headers Table 14. LVDS Data Connector Table 15. Backlight Inverter Voltage Selection Jumper Table 16. FPD Brightness Connector Table 17. Flat Panel Voltage Selection Jumper Table 18. System Fan Header Table 19. SATA Connectors Table 20. Front Panel Wireless Activity LED Header Table 21. Front Panel Audio Header for Intel HD Audio Table 22. Front Panel Audio Header for AC 97 Audio Table 23. Front Panel USB 2.0 Headers Table 25. Internal S/PDIF Header 56 Table 26. Parallel Port Header ECP Signal Name Standard Signal Name Pin 3.2.2.2 Add-in Card Connectors NOTE 3.2.2.3 Power Supply Connector 3.2.2.4 Front Panel Header Figure 12. Connection Diagram for Front Panel Header Page 3.2.2.5 Front Panel USB 2.0 Headers NOTE 3.3 BIOS Configuration Jumper Block Table 30. BIOS Configuration Jumper Settings 3.4 Mechanical Considerations 3.4.1 Form Factor 3.5 Electrical Considerations 3.5.1 Fan Header Current Capability 3.5.2 Add-in Board Considerations 3.6 Power Consumption 3.6.1 Minimum Load Configuration 3.6.2 Maximum Load Configuration 67 Parameter 3.7 Reliability 3.8 Environmental Specification 4 Overview of BIOS Features 4.1 Introduction 69 Table 35 lists the BIOS Setup program menu features. Table 35. BIOS Setup Program Menu Bar Exit 4.2 BIOS Flash Memory Organization 4.3 Resource Configuration 4.3.1 PCI* Autoconfiguration 4.4 System Management BIOS (SMBIOS) 4.5 Legacy USB Support 4.6 BIOS Updates 4.6.1 BIOS Recovery 4.6.2 Custom Splash Screen 4.7 Boot Options 4.7.1 Optical Drive Boot 4.7.2 Network Boot 4.7.3 Booting Without Attached Devices 4.7.4 Changing the Default Boot Device During POST 4.8 Adjusting Boot Speed 4.8.1 Peripheral Selection and Configuration 4.8.2 BIOS Boot Optimizations 4.9 BIOS Security Features 77 5 Board Status and Error Messages Pattern Type 5.1 BIOS Beep Codes Frequency 5.2 Front-panel Power LED Blink Codes Error Message Note Pattern Type 5.4 Port 80h POST Codes 80 Table 44. Port 80h POST Codes continued Port 80 Code Progress Code Enumeration 81 Table 44. Port 80h POST Codes (continued) continued Port 80 Code Progress Code Enumeration 82 Table 44. Port 80h POST Codes (continued) Port 80 Code Progress Code Enumeration 83 Table 45. Typical Port 80h POST Sequence POST Code Description 6 Assembly/Disassembly Guide 6.1 Introduction 6.2 Required tools 6.3 Board Installation Steps 6.4 Installing USB devices under the front plate 6.5 Installing SSD and Fans 7 Operating System Reference 7.1 Installing Windows* 7 7.1.1 Downloading and installing Windows 7 onto the Target SSD/HDD Page 7.1.2 Downloading and installing processor, graphics, chipset and other optional drivers 7.2 Installing Windows* Embedded Standard 7 7.2.1 Downloading, burning, and installing the WES7 DVD image 7.2.2 Install WES7 Page Page Page 7.2.3 Downloading and installing processor, graphics, chipset and other optional drivers 7.3 Installing Windows Embedded Compact 7* 7.4 Installing Windows XP* 7.4.1 Overview 7.4.2 F6 install with floppy Page Page Page 7.4.3 Slipstream install Page Page 7.4.4 Install Device Drivers 7.4.5 Install and configure EMGD 7.5 Using MeeGo* 7.5.1 Booting MeeGo* 7.5.2 Live Image on USB stick 7.5.3 Install with USB stick 7.5.4 Graphics Driver 7.5.5 Flash 7.6 Using Yocto Project* 7.6.1 Booting Yocto Project* 7.6.2 Live Image on USB stick 7.6.3 Install with USB stick 7.6.4 Install with CD or DVD 7.6.5 Graphics Driver 8 Battery Disposal