Speaker Connections, Connection Method #1 | JBL HTI88BB specification

SPEAKER CONNECTIONS

Connection Tips

Refer to page 4 of the HTI88 sub- woofer owner’s guide for general information on speaker-wire con- nections. This manual includes con- nection guidelines that are specific to the HTI88BB back box.

To use the push-type terminals on the connections panel supplied with the HTI88BB back box enclosure, depress the colored cap until the pass-through hole in the binding post is revealed. While holding the cap down, insert the bare end of the wire, or a banana plug, into the pass-through hole. Release the cap and tug gently on the wire to ensure that it is secure.

Since the HTI88 is a passive loud- speaker, only speaker-level connec- tions are available. Depending on whether you are using a dedicated subwoofer amplifier or your main receiver/amplifier to power the HTI88, select one of the two connec- tion methods that follow.

Connection Method #1

Use this method when you are using the HTI88 with your main receiver/ amplifier. Connect the main left and

right speaker-level outputs on your receiver/amplifier to the Input 1 (for left channel) and Input 2 (for right channel) connectors on the HTI88 connection panel. Connect the Output 1 terminals to the correspon- ding terminals on your front left speaker, and the Output 2 terminals to the corresponding terminals on your front right speaker.

NOTE: When using Connection Method #1 with only one HTI88, the shorting straps must be removed.

If you are using two HTI88 sub- woofers, connect the left speaker out- puts on your receiver/amplifier to Input 1 on one subwoofer’s connec- tions panel, and the right speaker outputs on your receiver/amplifier to Input 1 on the second subwoofer’s connections panel. Then connect Output 1 from the left-channel sub- woofer to the inputs on your main left speaker, and Output 1 from the right-channel subwoofer to the inputs on your main right speaker. When using the HTI88 in this mono mode, you should not remove the shorting straps.

Connection Method #2

Use this method when you are using the HTI88 with a dedicated sub- woofer amplifier. Connect your main receiver/processor’s line-level sub- woofer output to the line-level input on your subwoofer amplifier. Connect the speaker terminals on your subwoofer amplifier to either Input 1 or Input 2. If your amplifier has stereo outputs, you may con- nect one channel to each of Inputs 1 and 2. However, you must remove the shorting straps when using stereo mode. Alternatively, you may connect each channel to a separate HTI88. When using only one input on an individual HTI88, you should leave the shorting bars in place.

Using the HTI88BB Back Box Whichever connection method you choose, to install the HTI88BB back box, you will need to connect all of the eight wires coming out of the bottom of the back box to the appro- priate terminals on the loudspeaker. The wires are color-coded as follows:

INPUT 1 (–): Yellow with black stripe

INPUT 1 (+): Solid yellow

INPUT 2 (–): White with black stripe

INPUT 2 (+): Solid white

Connection Method #1, Using Two HTI88 Loudspeakers

With Back Boxes (Use Shorting Straps)

Receiver/Amplifier Speaker Outputs

Left

Right

–

Connections Panel of

Left HTI88BB Back Box

Right HTI88BB Back Box

YEL/BLK

YEL

WHT/BLK

WHT

ORG/BLK

ORG

GRE/BLK

GRE

YEL/BLK

YEL

WHT/BLK

WHT

ORG/BLK

ORG

GRE/BLK

GRE

–

INPUT 1

INPUT 2

OUTPUT 1

OUTPUT 2

INPUT 1

INPUT 2

OUTPUT 1

OUTPUT 2

Front Left Speaker

Front Right Speaker

–

Connection Method #2, Using Two HTI88 Loudspeakers

With Back Boxes (Use Shorting Straps)

OUTPUT 1 (–): Orange with black stripe

OUTPUT 1 (+): Solid orange

OUTPUT 2 (–): Green with black stripe

OUTPUT 2 (+): Solid green

Connection Method #1, Using One HTI88 With Back Box (Remove Shorting Straps)