T |
| R O U B L E S H O O T I N G |
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
If |
| there is no sound from any of | • If your receiver/processor is | If there is no sound from the | ||||||
| ||||||||||
the speakers: | set in Dolby Pro Logic mode, | surround speakers: | ||||||||
• Check that receiver/amplifier | make sure the center speaker | • Check all wires and | ||||||||
is on and a source is playing. | is not in phantom mode. | connections between | ||||||||
• Check that the powered | • If your receiver/processor | receiver/ amplifier and | ||||||||
subwoofer is plugged in, its | is set in Dolby Digital or DTS® | speakers. Make sure all wires | ||||||||
Power switch ¡ is switched | mode, make sure the | are connected. Make sure | ||||||||
on to the “ON•” position. | receiver/processor is con- | none of the speaker wires are | ||||||||
• Check all wires and | figured so that the center | frayed, cut or punctured. | ||||||||
connections between | speaker is enabled. | • Review proper operation of | ||||||||
receiver/ amplifier and |
|
| your receiver/amplifier and its | |||||||
speakers. Make sure all wires | If the system plays at low | |||||||||
are connected. Make sure | volumes but shuts off as | • Make sure the movie or TV | ||||||||
none of the speaker wires are | volume is increased: | show you are watching is | ||||||||
frayed, cut or punctured. | • Check all wires and connecti- | recorded in a | ||||||||
• Review proper operation of | ons between receiver/ | mode. If it is not, check to see | ||||||||
your receiver/amplifier. | amplifier and speakers. Make | if your receiver/ amplifier has | ||||||||
|
|
|
| sure all wires are connected. | other surround modes you | |||||
If there is no sound coming | Make sure none of the | may use. | ||||||||
from one speaker: | speaker wires are frayed, cut | • In Dolby Digital or DTS® |
| |||||||
|
| |||||||||
• Check the “Balance” control | or punctured. | modes, make sure your |
| |||||||
on your receiver/amplifier. | • If more than one pair of main | receiver/processor is |
| |||||||
• Check all wires and con- | speakers is being used, check | configured so that the |
| |||||||
nections between receiver/ | the minimum impedance | surround speakers are | ||||||||
amplifier and speakers. Make | requirements of your | enabled. | ||||||||
sure all wires | are connected. | receiver/amplifier. | • Review the operation of your | |||||||
Make sure none of the |
|
| DVD player and the jacket of | |||||||
speaker wires are frayed, cut | If there is low (or no) bass | your DVD to make sure that | ||||||||
or punctured. | output: | the DVD features the desired | ||||||||
• In Dolby Digital or DTS® | • Make sure the connections to | Dolby Digital or DTS® mode, | ||||||||
modes, make sure that the | the left and right “Speaker | and that you have properly | ||||||||
receiver/processor is | Inputs” have the correct | selected that mode using both | ||||||||
configured so that the | polarity (+ and | the DVD player’s menu and | ||||||||
speaker in question is | • Make sure the subwoofer is | the DVD disc’s menu. | ||||||||
enabled. | plugged into an active |
|
|
|
|
| ||||
|
|
|
| electrical | outlet. |
|
|
|
|
|
If there is no sound from the | • Make sure | the powered |
|
|
|
|
| |||
center speaker: | subwoofer | is plugged in and |
|
|
|
|
| |||
• Check all wires and | switched on. |
|
|
|
|
| ||||
connections between | • In Dolby Digital or DTS® |
|
|
|
|
| ||||
receiver/ | modes, make sure your |
|
|
|
|
| ||||
amplifier and speaker. Make | receiver/processor is |
|
|
|
|
| ||||
sure all wires are connected. | configured so that the |
|
|
|
|
| ||||
Make sure none of the | subwoofer and LFE output are |
|
|
|
|
| ||||
speaker wires are frayed, cut | enabled. |
|
|
|
|
| ||||
or punctured. |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
10