![Dolby Pro Logic (Non-Digital) – Line Level](/images/new-backgrounds/16226/1622615x1.webp)
Dolby Pro Logic |
|
| |||||||
Use this installation method for |
| preamp | LFE input on the subwoofer | ||||||
Dolby Pro Logic |
| Use | with Dolby Pro Logic | ||||||
(not Dolby Digital, DTS® or |
|
| to connect the | processors. Note: If your | |||||
other digital processing), where |
| subwoofer outputs on your | receiver or amplifier only has | ||||||
the receiver/processor is |
|
| receiver or amplifier to the line- | one subwoofer output jack, | |||||
equipped with a subwoofer |
|
| level inputs on the subwoofer. | then you will need to use a Y- | |||||
output, or a |
| IMPORTANT: Do not use the | connector (not included). Plug | ||||||
|
|
|
|
|
|
|
|
| the male end of the Y- |
Left Front |
| Center |
|
| Right Front | connector into your receiver or | |||
| + | – |
| amplifier’s subwoofer output | |||||
|
|
|
|
|
| ||||
+ | – |
|
|
|
|
| + | – | jack, and connect each of the |
|
|
|
|
|
|
|
|
| two female ends to separate |
|
|
| Subwoofer |
|
|
| |||
|
|
|
|
|
| plug the | |||
|
|
| Line- |
|
|
|
| ||
|
|
|
|
|
|
| into the | ||
|
|
| Level |
|
|
|
| ||
|
|
| In |
|
|
|
|
| subwoofer. |
|
|
| L |
|
|
|
|
| |
|
|
|
|
|
|
|
| Connect each speaker to the | |
|
|
|
|
|
|
|
|
| |
|
|
| R |
|
|
|
|
| corresponding speaker |
|
|
| Receiver |
|
|
|
| terminals on your receiver or | |
| Left |
| Subwoofer | Right |
|
| amplifier. | ||
| Front |
| Out |
|
| Front |
|
|
|
| + | – |
|
|
| + | – |
|
|
|
|
| R | L |
|
|
|
| |
| Left |
| Center |
| Right |
|
| ||
| Rear |
|
| Rear |
|
|
| ||
| + | – | + | – |
| + | – |
|
|
Left Surround |
|
|
|
|
| Right Surround |
| ||
+ | – |
|
|
|
|
| + | – |
|
Dolby Digital or DTS® (or Other Digital Surround Mode) Connection
| RECEIVER | SUBWOOFER | output or subwoofer output | Note: | |||||
|
|
|
|
|
|
|
| ||
|
|
|
| LINE LEVEL IN | on your receiver or amplifier. | When using the LFE input, the | |||
|
|
|
|
|
| L |
| Connect each speaker to the | subwoofer's Crossover control |
| LFE OUT |
| LFE INPUT | ||||||
|
| corresponding speaker | is NOT active, because this | ||||||
|
|
|
|
|
| R |
| ||
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| terminals on your receiver or | function is controlled by your |
|
|
|
|
|
|
|
| amplifier. | surround processor. |
| Use this installation method for | ||||||||
| Make sure that you have | When using the LFE input, set | |||||||
| Dolby Digital, DTS® or other | configured your surround- | the subwoofer's Volume control | ||||||
| digital surround processors: | sound processor for | to "Max" and calibrate the | ||||||
| Use the | “Subwoofer On.” The front left, | subwoofer level along with the | ||||||
| marked “LFE” for the Low- | front right, center and rear | other speakers according to | ||||||
| Frequency Effects channel. | speakers should all be set to | the | ||||||
| Connect this jack to the LFE | “Small.” | owner's manual for your | ||||||
|
|
|
|
|
|
|
|
| surround receiver/amplifier. |
8