Vertically Stand-Mounting the Receiver Module

Step 1.

Remove the corner screws located on the left side of the receiver module when viewed from the bottom, looking at the front, as shown in Figure 8.

MAINTENANCE AND SERVICE

All wiring connections should be inspected and cleaned or remade periodically. The frequency of maintenance depends on the metals involved in the connec- tions, atmospheric conditions and other factors, but once per year is the minimum.

In the event that your system ever needs service, contact your local JBL dealer or distributor, or visit www.jbl.com for a service center near you.

Figure 8.

Step 2.

Rest the receiver module on top of the stand and reattach the two screws that were removed in Step 1 through the holes in the stand into the bottom of the receiver module, as shown in Figure 9.

Figure 9.

Step 3.

Rotate the JBL logo 90˚ by gently pulling it out and turning it.

Vertically Mounting the

Transmitter Module

Step 1.

Attach the four included self-adhesive rubber feet in the recesses on the side of the transmitter module.

Step 2.

Rotate the JBL logo to a vertical orientation.

SPECIFICATIONS

Frequency Range:

20Hz – 20kHz

(+0dB, –1dB)

 

Amplifier Output:

50 Watts per channel

Signal-to-Noise Ratio:

80dBA

Operating Range:

Up to 70' (22m), depending upon conditions

RF Operating Frequency:

2.4GHz

Power Requirement:

100V – 240V AC, 50/60Hz

Dimensions

 

Transmitter Module:

1-1/8" x 6" x 3-7/8" (29mm x 154mm x 98mm)

(H x W x D)

3-3/4" (95mm) high with antenna extended

Receiver Module:

1-1/8" x 6-3/16" x 4-5/8" (29mm x 158mm x 116mm)

(H x W x D)

3-3/4" (95mm) high with antenna extended

Weight

 

Transmitter Module:

0.6 lb (0.3kg)

Receiver Module:

0.9 lb (0.4kg)

Features, specifications and appearance are subject to change without notice.

Remote Control Battery Replacement

CAUTION:

When replacing the lithium battery in the remote, make sure that the replacement battery is inserted in correct polarity. Place the battery so that its positive (+) side faces up with the tray held so that the surface with the dot and/or with a (+) mark next to the part number is facing up.

Remote control battery installation

Push small tab

Pull battery

Insert new battery

toward battery slot.

drawer out.

with “+” side up, and

 

 

slide battery drawer

 

 

back into remote.

CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE (CR2025).

WARNING: DO NOT EXPOSE BATTERIES TO EXCESSIVE HEAT SUCH AS DIRECT SUNLIGHT, FIRE OR THE LIKE.

Dispose of dead batteries in accordance with local regulations.

Declaration of Conformity

We, Harman Consumer Group, Inc.

2, route de Tours

72500 Château du Loir

France

declare in own responsibility that the product described

in this owner’s manual is in compliance with technical

standards:

EN 55013:2001+A1:2003

EN 55020:2002+A1:2003

EN 61000-3-2:2000

EN 61000-3-3:1995+A1:2001

EN 60065:2002

Laurent Rault

Harman Consumer Group, Inc.

Château du Loir, France 10/08

Page 6 Page 8
Page 7
Image 7
JBL Professional WEM-1 manual Maintenance and Service, Specifications, Vertically Stand-Mounting the Receiver Module
Page 6 Page 8

WEM-1 specifications

The JBL Professional WEM-1 is a remarkable wall-mounted loudspeaker that epitomizes the blend of innovative technology and exceptional audio performance. Designed primarily for professional environments such as conference rooms, auditoriums, and public spaces, the WEM-1 offers a reliable sound solution that caters to a variety of applications.

One of the standout features of the WEM-1 is its compact and sleek design, allowing it to blend seamlessly into different architectural styles while delivering rich, detailed sound. The speaker employs JBL’s advanced driver technology, which includes a high-quality, low-frequency driver that provides robust bass response and a soft dome tweeter which is adept at producing clear, extended high frequencies. This combination results in a balanced audio output that can easily fill a room without distortion, regardless of volume levels.

The WEM-1 is engineered with versatility in mind. It offers multiple mounting options and can be installed in various orientations, making it ideal for different room layouts and user needs. Additionally, the speaker features a built-in transformer that allows for easy integration into 70V or 100V distributed sound systems, which is essential for large-scale installations where multiple speakers are employed.

Another notable characteristic of the WEM-1 is its robust construction. The enclosure is made from durable materials that can withstand the rigors of continuous use, making it suitable for commercial applications. Its weather-resistant design is another plus, allowing it to perform optimally in outdoor settings, where exposure to elements is a concern.

The WEM-1 is not only user-friendly but also equipped with a range of connectivity options to facilitate seamless integration with various audio sources. This flexibility ensures that it can accommodate different audio setups, whether for presentations, background music, or engaging announcements.

Overall, the JBL Professional WEM-1 stands out as a high-quality, dependable loudspeaker that combines rich sound reproduction with practical installation features. Its technology and design cater to the needs of professionals seeking an effective audio solution in both indoor and outdoor settings, making it an exceptional choice for various sound reinforcement projects.
Top Page Image Contents