Jensen JiMS-211i owner manual Installation, Location of Controls

INSTALLATION

Clock setting battery back-up

The battery back-up compartment is located at rear of the unit.

(1)Remove the battery compartment door.

(2)Follow the polarity diagram shown inside the compartment and install 2 x AAA batteries (not included).

(3)Replace the battery compartment door.

WARNING:

-Be sure that the batteries are installed correctly. Wrong polarity may damage the unit.

-Do not mix old and new batteries.

-Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.

-Only batteries of the same or equivalent type as recommend are to be used.

-If the unit is not to be used for an extended period of time, remove the battery.

-Do not dispose of batteries in ￿ re, batteries may explode or leak.

Battery Low indication

If the battery low indicat or blinks on LCD display, replace the back-up battery with fresh one.

AC-DC Adaptor Connection

The unit is powered by an external AC-DC Power Adaptor with an output of 8V DC / 2000mA (included).

(1)Plug the adaptor into an outlet rated at 120V AC / 60Hz.

(2)Insert the adaptor's DC output plug into the DC-IN jack on the back of the unit.

NOTE: This unit is not magnetically shielded and may cause color distortion on the screen of some TVs or video monitors. T o avoid this, you may need to move the unit further away from the TV or monitor if unnatural color shifts or image distortion occurs.

PROTECT YOUR FURNITURE!!

This system is equipped with non-skid rubber ‘feet’ to prevent the product from moving when you operate

the controls. These ‘feet’ are made from non-migrating rubber material specially formulated to avoid leaving

any marks or stains on your furniture. However certain types of oil based furniture polishes, wood preservatives, or cleaning sprays may cause the rubber ‘feet’ to soften, and leave marks or a rubber residue on the furniture.

To prevent any damage to your furniture we strongly recommend that you purchase small self-adhesive felt pads, available at hardware stores and home improvement centers everywhere, and apply these pads to the bottom of the rubber ‘feet’ before you place the product on fine wooden furniture.

5

LOCATION OF CONTROLS

Main Unit

Top view

10 9 8 7 4 5 6

11 3

2	1
Rear view	Front view

20 15 16 18 13 14 12 13

1719

1.iPod/iPhone docking station

2.iPod/iPhone docking connector

3. POWER On/Off			button -----	Turns the unit on or standby.
4.	Function	button	----- Select	FM RADIO, iPod/iPhone, AUX modes.
5.	SLEEP	button	----- Select	the time duration of the sleep timer.

6.CH+/- button ----- Select preset radio station.

7.VOLUME wheel/ MODE button

MODE button -----	In standby mode, press to adjust clock and alarm setting.
In FM radio		mode, press to select FM stereo or mono reception.
VOLUME wheel -- Rotate		to adjust the volume level up or down;
	Rotate to adust hour/minute of clock/alarm.

8.SNOOZE/DIMMER button ----- Activate the snooze function; turn LCD backlight Bright/DIM/OFF .

9. PRESET /			button	Save radio	preset station; iPod/iPhone play-pause.
10.	/	button		In iPod/iPhone mode, skip tracks Forward / Backward or perform
			high-speed search.
11. ALARM			In Radio mode,		turn the radio frequency up/down.
		button -----		Turn the alarm on and off.

12.LCD display

13.Pair of Speakers

14.	Remote Infrared		Sensor
15.	Battery Compartment
16. AUX IN		jack : Auxiliary audio signal input.
17.	RCA VIDEO Jack		------ Composite video signal output.
18.	DC-in	jack : For	the connection of external DC power supply.
19.	RESET	button ----- For resetting the unit.

20. FM Antenna wire

6