Jensen SOOGM-16 instruction sheet Buick, Cadillac, Chevrolet, Gmc, Hummer, Pontiac, Saturn

Rev. 082113

ONSTAR RADIO REPLACEMENT FOR SELECT GM LAN 29-BIT VEHICLES 2006-UP

INTERFACING SOLUTIONS

SOOGM-16

SOOGM-16A

Harness: 2606 Only. Covers 2012-UP Pick-Ups w/ Navigation listed below.

BUICK:

2008 - 2012 Enclave

2006 - 2011 Lucerne

CADILLAC

2006 - 2010 DTS

2007 - 2013 Escalade

2007 - 2009 SRX

We recommend reading this installation guide first before starting any work. Following these instructions from “Start” to” Finish” will ensure a smooth and hassle free installation. We offer telephone support M-F 9:00 AM – 5:00PM PDT at 1 (855) 822-1348. We are here to help.

PARTS INCLUDED:

(1) Interface Module

(1)GM 29-Bit Harness (Part Number: Crux2513)

(1)Instruction Sheet

(1)Reverse Camera Harness (CJA2103A)

PRECAUTIONS:

-Remove the negative side of the battery to avoid any short circuits durring the installation.

-Do not install the interface near any major components or near the HVAC system. This may cause damage or overheating to the vehicle.

PRELIMINARY:

Please read the entire mannual before installing this interface. This unit provides the following:

- 12V Acc Output (3A Max/ RAP)

- Illumination Output (250mA Max)

- Low Voltage (Batt Run-Down Protection)

OVERVIEW OF INSTALLATION	CONNECT THE WIRES,
MATCH LOOSEWIRES TO AFTERMARKET RADIO	COLOR FOR COLOR.
		front left speakers
		front right speakers
		rear left speakers
		rear right speakers
AFTERMARKET		constant
		illumination
		accessory
RADIO		ground
		vss
		amp on
		swc
	MUTE	8-PIN
	CIRCUIT
	BOARD	(male plug)
	(SEE FIG 1)

CHEVROLET:

2007 - 2013 Avalanche*

2007 - 2009 Equinox

2008 - 2011 Express Van

2006 - 2013 Impala/ Impala SS

2006 - 2007 Monte Carlo

2007 - 2013 Silverado* 1500-3500 Pickup

2007 - 2013 Suburban*

2007 - 2013 Tahoe*

2009 - 2012 Traverse

GMC:

2007 - 2012 Acadia

2008 - 2011 Savana

2007 - 2013 Sierra 1500-3500 Pickup*

2007 - 2013 Yukon*

HUMMER:

Chimes Include:

- Seatbelt

- Check Engine

- Key In Ignition

- Low Fuel

- Low Oil

- Lights On

Before installing this interface please review the options before removing the factory radio. Some options may need to be adjusted prior to removing the factory radio. Options include:

-Standard BOSE Amplifier

-Premium Bose (Y-91)

IMPORTANT:

- The Front and Rear fading are not retained on Y-91 BOSE. - The Onstar volume output is defaulted to low-gain

(male plug)	INTERFACE
12-PIN
THIS HARNESS ONLY HAS
3-PINSPOPULATED.		8-PIN
DO NOT PLUG IN THE
FULLY POPULATED 8-PIN.		(male plug)

16-PIN

24-PIN(male plug) (male plug)

14-PIN

(male plug)

TO FACTORY

HARNESS

2008 - 2009 H2

PONTIAC:

2007 - 2009 Torrent

SATURN:

2007 - 2009 Outlook

2008 - 2009 Vue

SUZUKI:

2007 - 2008 XL7

*2012 Vehicles with Navigation Units are not supported. Needed is SOOGM-16A

Tech Tip:

Make sure to wipe the 3.5mm plug before inserting into the aftermarket radio to avoid a bad connection.

This Interface Supports:

-BOSE Amplifier

-Y-91 System

-Rear Seat Entertainment*

-Back-Up Camera

WIRING COLOR CODES

Black	= Ground
Red	= Accessory
Yellow	= Constant
Orange	= Illumination
Blue/White	= Amplifier Turn-On
White	= Left Front (+)
White/Black	= Left Front (-)
Gray	= Right Front (+)
Gray/Black	= Right Front (-)
Green	= Left Rear (+)
Green/Black	= Left Rear (-)
Purple	= Right Rear (+)
Purple/Black	= Right Rear (-)
Purple/White	= Vehicle Speed Sense
Blue/Yellow	= SWC (Kenwood/ JVC)
Orange/White	= Dimmer
Yellow/Black	= Parking Brake
Red/White	= Reverse Gear

USING THE SWC WIRE ON NEW JVC UNITS

New JVC units no longer carry the 3.5mm cable and have added the SWC signal via a Lt. Blue/Yellow wire.

This wire needs to be connected to the SWC wire labeled “Kenwood” also Lt. Blue/Yellow. Be sure to keep the dial switch set to number 4 when using JVC units.

ADJUSTING THE GAIN

High Gain (Non-Bose Systems)

Press OnStar button, Heear “Onstar Ready“, Turn Dial knob to “9“, Wait 4 seconds, Press Onstar button “Thank you Good Bye“.

Turn Dial knob back to Aftermarket radio corresponding.

The insterface is defaulted at Low-Gain.(BOSE Systems)

REAR SEAT ENTERTAINMENT (SPECIAL ORDER)

1.Conect the rear seat entertainment 16-Pin connector to the vehicles 16-Pin factory connector.

2.Connect the RCA’s to the aftermarket radio video and audio input.

3.Test the video and audio before installing the radio into the dash.

GRAY		AUXA/V	OVERHEADTO SCREEN
	GMCRUXONSTARLAN
Connector
			Connect to
			Ground
Must Special Order Harness: CJA2333A
RADIO REMOTE SELECT:
0.	Pioneer		Use a small screw
1.	Alpine		driver to make
2.	Clarion		adjustments.
3. Kenwood			Note: Seek Up is not
4.	JVC
			supported on Jensen
5.	Sony/Jensen/Dual		radios.

USING THE MUTE CIRCUIT BOARD (FIG 1)

The external mute circuit is used to mute the audio on your radio. Determine whether your radio is equipped with BOSE, then place the 8 pin connector into the proper female connector. Reference the sticker on the mute circuit board. BOSE

8-PIN

(male plug)

Non-BOSE

BACK-UP CAMERA CONNECTION

1.Conect the back-up camera 16-Pin connector to the vehicles 16-Pin factory connector.

2.Connect the yellow video RCA to the new aftermarket radio video input.

3.Test the video feed before installing the radio back into the dashboard.

	CRUX GMLAN ONSTAR BACK UP CAMERA
Part Number: CJA2103A

The module has been rated for upto 3A max of output.

For applications demanding a continuous output of 3A or more, we reccomend using a standard BOSCH (SPDT) relay.

See your local car audio specialist.