Operating Instructions

[RESET] Button

VM9311TS

Power On / Off

Press the/MUTE button (7) to turn the unit on. The buttons on the front of the unit light up and “WELCOME” appears briefly in the LCD panel (23), followed by the current mode status. If the TFT screen is open, only the current mode status is displayed. You can also turn on the unit by pressing the OPEN button (1) and opening the TFT screen.

Press and hold the/MUTE button (7) on the front panel or the POWER button (4) on the remote to power off the unit.The monitor is drawn back into the main compartment and the LCD screen displays “BYE BYE”.

Audible Beep Confirmation

An audible beep tone confirms each function selection. The beep tone can be disabled through the System Setup menu.

Mute

Press the/MUTE button (7) on the front panel or the MUTE button (3) on the remote to mute the volume from the unit. Press the MUTE button again to restore the volume. “MUTE” is displayed on the LCD monitor. Adjusting the volume or using any of the audio setup features cancels the mute function.

Playing Source Selection

Press the SRC button (15) on the front panel or the SRC button (8) on the remote to change between available playing sources in the following order: TUNER, DVD, AUX IN, iPod and XM. The playing mode is displayed on the TFT and LCD screens.

AUX IN Mode

An external peripheral device can be connected to this unit via RCA output and “AUX-IN”.

Volume Adjustment

To increase or decrease the volume level, turn the ROTARY ENCODER (6) on the front panel or press the VOL+/ VOL- buttons (15, 16) on remote control. When the volume level reaches “0” or “40”, a beep sounds, indicating that the adjustment limit has been reached. The volume ranges from “0” to “40”. The LCD or TFT screen displays the volume level for 3 seconds.

Programmable Turn-On Volume

This feature allows the user to select a turn-on volume setting regardless of the volume setting prior to turning the unit off. To program a specific volume level, push and hold the VOL/ LO/DX knob (6) while the yellow volume bar is displayed on

the screen. The unit will beep two times to confirm your turn- on volume setting.

Audio Control Menu

The Audio Control feature allows you to easily adjust your audio system to meet the acoustical characteristics of your vehicle, which vary depending on the type of vehicle and its measurements. To get the best possible sound quality from your new system, be sure to adjust the settings for the speakers as well. Proper setting of the Fader and Balance boosts the effects of the cabin equalizer.

Accessing the Audio Control Menu

Press the VOL/LO/DX knob (6) on the front panel once to display the “AUDIO” menu.

Selecting an Audio Feature for Adjustment

Continuously press the VOL/LO/DX knob (6) on the front panel, or press the (>>)/(<<) buttons (14, 22) on the remote control or the (/\)/(V) buttons (18, 19) on the joystick to select the audio feature to be adjusted.

Adjusting an Audio Feature

Rotate the VOL/LO/DX knob (6), press the (<<)/(>>) buttons (17, 19) on the remote control, or press the (<)/(>) buttons

(16, 17) on the joystick to adjust the selected feature to the desired setting.

Table 4: Audio Adjustments

Audio Function	Adjustable Range


EQ	User
	Flat

	Jazz

	Pop
	Classical

	Rock

	Vocal
BASS	-14 to +14

TREBLE	-14 to +14

SUB	-7 to +7
LOUD	0 (off), 1-4

FAD (Fade)	-9 to +9

BAL	-9 to +9

NOTE: The Bass and Treble levels are only adjustable when EQ is set to “User” mode.

Loudness

The Loud function compensates for deficiencies in sound ranges at low levels. Loudness levels range from 1-4 or “off”. The Loudness level/function is dependent on the main volume setting. As the volume is increased, less Loudness compensation is applied to the audio signal. This is referred to "Auto-Loudness". The possible loudness settings are as follows:

•Off

•1 - Slight bass boost at low volume level

•2 - Moderate bass boost at low volume level

•3 - Good bass boost at low to mid volume level

•4 - maximum bass boost at mid volume level

When the Loud function is on, “LOUD” is displayed on the screen.

Exiting the Audio Control Menu

Press and hold the VOL/LO/DX knob (6) or stop making adjustments for a few seconds to exit the audio control menu.

System Reset

To correct a system halt or other illegal operation, use the tip of a pen

to press the RESET button (22)

located on the front bottom-right corner of the unit. After a system reset, the unit restores all factory default settings.

NOTE: If the unit is reset while a DVD is playing, the DVD resumes play once the reset is complete.

Line Mute

If the “MUTE” wire is connected, audio output mutes when a telephone call is received by the car phone or when verbal navigation is performed.

Jensen vm9311ts instruction manual Operating Instructions

Models: vm9311ts