Maintenance, Blade selection | Jet Tools CS-315, CS-275 specs

7.Pull the operating lever to bring down the blade into the work piece. You will manually control the speed of the downstroke.

8.When the cut is complete, release the trigger and raise the head. The spring will help return the head to upward position.

9.Release the vise using the handwheel, and remove the work piece.

NOTE: When operations are complete, always return the head to upward position to relieve stress on the return spring.

13.0Maintenance

13.1Maintenance requirements

All maintenance and cleaning procedures must be performed with the power switched OFF. Failure to comply may result in serious injury!

On completion of maintenance, ensure that replaced parts and/or any tools used have been removed from the machine before starting it up.

13.2Periodic maintenance

Remove all swarf from the machine, preferably with a cloth.

Remove chips from the coolant tank and change coolant regularly.

Top off the coolant level.

Check the wear of the blade and change if necessary (see Blade Replacement).

Empty the chips out of the base.

Clean the vise and lubricate all the joints and sliding surfaces, using good quality oil.

Attend to daily, weekly and annual lubrication recommendations (see the Lubrication section).

13.3Coolant system

Check coolant level in the tank periodically and top off if necessary. Coolant can also be added by pouring directly on the table, which will drain into the tank through the filter plate.

This coolant system can operate with either a soluble oil base coolant or water-soluble synthetic coolant. Coolant should be changed regularly. Some recommended brands are DoAll and Lenox. These coolants are available at your local industrial distributor.

Periodically remove excess chips from the coolant tank, and clean the filter on the coolant pump.

13.4Lubrication

For long life and trouble free operation, it is essential that this machine is kept well lubricated. The vise and leadscrew should be oiled daily. Pivot joints and bearings should be greased weekly. Check the gearbox oil level weekly, full level is top of sight glass with head in full up position.

The gearbox oil should be changed out after the first 100 hours of operation, then after every 2,000 working hours. Drain the gearbox by unscrewing the plug on the side of the head (Figure 14). To re- fill the head, remove the operating lever and pour oil into the hole. The plug also serves as the oil level sight glass. Full level is top of sight glass with head in full up position.

Follow local regulations for proper disposal of used lubricants.

Recommended Lubricants:

Gearbox

Use Texaco Meropa® 460 or equivalent.

Grease fittings

Texaco Starplex® 2 or equivalent

Vise and Leadscrew

Regal® R & O 68

Figure 14

14.0Blade selection

When using the cold saw, it is important to select the correct type of blade for the material to be cut. This section explains the limitations and specific applications of the different types of blades.

14.1General characteristics

Fine Tooth Pitch – used for thin wall materials such as sheet steel, tubes and profiles.

Coarse Tooth Pitch – used for large cross-sections, and for soft materials (aluminum alloys and soft alloys in general).

CS-315, CS-275 specifications

Jet Tools has a long-standing reputation for delivering quality woodworking and metalworking machinery, and their CS-275 and CS-315 bandsaw models exemplify that commitment to excellence. Designed with both professional woodworkers and hobbyists in mind, these saws are engineered to provide precision, power, and ease of use.

The CS-275 features a robust design that includes a heavy-duty cast iron frame providing stability and reducing vibration during operation. This enhances the accuracy of cuts. With a 2.5 HP motor, the CS-275 delivers ample power for most woodworking tasks, enabling users to tackle various materials, from softwoods to hardwoods. Its easy-to-read scale and quick blade change system make blade adjustments seamless. The saw blade can accommodate a range of widths, allowing users to switch between intricate cuts and larger operations without hassle.

On the other hand, the CS-315 takes it a step further with a 3 HP motor, catering to those who need more power for demanding projects. This model boasts an extended cutting capacity, which is perfect for larger workpieces. The dual table support system ensures maximum stability, while the integrated dust collection port helps maintain a clean work environment by minimizing debris and sawdust.

Both models incorporate Jet's advanced technology that prioritizes user safety and comfort. Features such as an oversized handwheel and a precision tensioning system allow for easy adjustments of the blade, ensuring optimal performance. The CS-275 and CS-315 are equipped with high-quality bearings and a precision ground cast iron table that provides a smooth surface for cutting, enhancing performance and longevity.

Additionally, these bandsaws share a common feature: a large viewing window that allows users to monitor their cutting line easily. This ensures that every cut is precise and increases overall productivity. The saws also come with a solid standard warranty, underscoring Jet Tools' confidence in their durability and quality.

In summary, whether you choose the CS-275 or the more powerful CS-315, Jet Tools offers robust construction, innovative technologies, and user-centered design. Both models are excellent additions to any workshop, providing reliability and performance that professionals and enthusiasts alike will appreciate.

Jet Tools CS-315, CS-275 operating instructions Maintenance, Blade selection

Models: CS-315 CS-275