S T E P 4
Line up the Stealthbox® so that the seat belt anchor bolt is centered in the recess in the enclosure. Press down on the Stealthbox making and imprint in the 3” x 3” wax square with the Mounting Stud. Remove the Stealthox® and drill a 1/2” hole through the floor where the mark was made.
Before drilling, always make sure that you are not going to be drilling into any gas lines, brake lines, tires, transmission lines, electrical wiring, exhaust systems or anything else that might cause a reduction in your weekly pay.
Always wear eye protection when drilling!
S T E P 5
Back the Mounting Stud out of the Stealthbox® so that approximately
S T E P 6
Install the included Fender Washer, Split Lock Washer and Hex Nut as shown, tighten them down.
S T E P 7
C O N G R A T U L A T I O N S !
You have completed the installation for this model!
Enjoy your new Stealthbox®!
Please refer to the Power Recommendation section for an amplifier recommendation and basic
I N C L U D E D H A R D W A R E
1) | 1) | 3/8 x | |
1) | 3/8” Split Lock Washer | 1) |
S P E C I F I C A T I O N S
Enclosure Type: Acoustic Suspension (sealed)
Driver Type: (2)
Nominal Impedance: 4 ohms
Continuous Power Handling: 600 watts
P o w e r R e c o m m e n d a t i o n
JL Audio recommends high quality amplifiers such as the JL Audio HD900/5, 500/1v2 or J2 500.1. The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 500/1v2. If another amplifier is being used, please reference this illustration and use similar settings on that amplifier.
+12VDC Ground Remote | Preamp Output Section | Infrasonic Filter | “Q” | Center Freq. Boost (dB) Amp LP Filter | Amplifier Input Section | Subwoofer Output |
Output Mode | Filter Slope |
| Mode |
| 1.6 |
| 40 | +10 |
| Mode Slope | Input Voltage | Input Sens. | Signal Sensing | ||
| 1.1 | 2.7 | 30 | 60 | +4 | +13 | |||||||||
|
|
|
|
| 0.7 |
| 25 | 75 |
|
|
|
|
|
|
|
Full Range Amp Filter Out Filter | 12dB 24dB |
| Off On | 0.5 | 4.3 | 20 | 80 | 0 | +15 | Off 12dB 24dB | Low High |
| Off On | ||
|
| 65 | Filter Mode | 30 |
| Bass EQ |
|
|
|
|
| 65 |
|
|
|
| 55 | 80 | 22 | 45 |
|
| Advanced | 55 | 80 |
|
|
| |||
500/1v2 |
|
|
|
|
|
|
|
|
|
|
|
|
| ||
45 | 100 |
| 18 | 55 |
|
|
| Bass |
| 45 | 100 |
|
| MONO OUTPUT ONLY | |
Monoblock Subwoofer Amplifier | 40 | 200 | LP HP | 15 | 60 | Off On |
|
| Control |
| 40 | 200 |
|
| |
Left Output Right Output | Filter Freq. (Hz) | Infrasonic Freq. (Hz) | Remote Bass Port | Filter Freq. (Hz) | Left Ch. | Right Ch. |
All JL Audio amplifiers are very versatile audio components. Please consult the owner’s manual for even more detailed information about installing and tuning your amplifier.
C o n n e c t i o n s
Using quality power, signal and speaker wire is essential in ensuring the performance of your Stealthbox®. JL Audio recommends using a 4 AWG power kit such as the
M I D / H I G H F r e q u e n c y D r i v e r F I T M E N T
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.
Front Speaker Size / Location: 5”x 7” / 6”x 8”- Front Doors
Fits JL Audio Models:
Rear Speaker Size / Location: 5”x 7” / 6”x 8”- Rear Door
Fits JL Audio Models:
(954)
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.
Page 2 • JL Audio, Inc 2009
1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y • M I R A M A R , F L O R I D A • 3 3 0 2 5 • U S A
