JL Audio J2320.4 Product Description, Power Connections, Many vehicles employ small 10 AWG

Product Description

The JL Audio J2-320.4 is a four-channel, full- range audio amplifier utilizing

Class B technology for all channels.

The J2-320.4 can be operated with a wide variety of source units and system configurations. For detailed specifications, please refer to Appendix B (page 13).

Typical Installation Sequence The following represents the sequence

for a typical amplifier installation, using an aftermarket source unit or OEM Interface product. Additional steps and different procedures may be required in some applications. If you have any questions, please contact your authorized JL Audio dealer for assistance.

 1) Disconnect the negative battery post connection and secure the disconnected cable to prevent accidental re-connection during installation. This step is not optional.

 2) Run 4 AWG power wire from the battery location to the amplifier mounting location, taking care to route it in such a way that it will not be damaged and will not interfere with vehicle operation. Use 2 AWG or larger power wire and a power distribution block if additional amplifiers are being installed with the J2-320.4.

 3) Connect power wire to the positive battery post. Fuse the wire with an appropriate fuse block (and connectors) within 18 inches (45 cm) wire length of the positive battery post.

This fuse is essential to protect the vehicle. Do not install the fuse until the power wire has been securely connected to the amplifier.

 4) Run signal cables and remote turn-on wire from the source unit to the final amplifier mounting location.

 5) Run speaker cables from the speaker systems to the amplifier mounting location.

 6) Find a good, solid metal grounding point close to the amplifier and connect the negative power wire to it using appropriate hardware. Use the same size power wire as the wire connected to the “+12VDC” connection

(minimum 4 AWG), no longer than 36 inches (90 cm) from the amplifier to the ground connection point. In some vehicles, it may be necessary to upgrade the battery ground wire. (See page 5 for important notice).

 7) Securely mount the amplifier using

appropriate hardware.

 8) Connect the positive and negative power wires to the amplifier.

 9) Connect the remote turn-on wire

to the amplifier.

10)Connect the input cables to the amplifier.

11)Connect the speaker cables to the amplifier.

12)Carefully review the amplifier’s control settings to make sure that they are set according to the needs of the system.

13)Install the power wire fuse (60A for a single J2-320.4) and reconnect the negative battery post terminal.

14)Turn on the source unit at a low level to double-check that the amplifier is configured correctly. Resist the temptation to crank it up until you have verified the control settings.

15) Make necessary adjustments to the input sensitivity controls to obtain the right overall output and the desired balance in the system. See Appendix A (page 12) for the recommended input sensitivity setting method.

16)Enjoy the fruits of your labor with your favorite music.

Power Connections

Before installing the amplifier, disconnect the negative (ground) wire from the vehicle’s battery. This will prevent accidental damage to the system, the vehicle and your body during installation.

+ ￿￿VDC Remote

0A

The J2-320.4’s “+12VDC” and “Ground” connections are designed to accept 4 AWG power wire. 4 AWG is a minimum power wire size for this amplifier.

If you are installing the J2-320.4 with other amplifiers and wish to use a single main power wire, use 2 AWG or larger main power wire (depending on the overall current demands of all the amplifiers in the system). This 2 AWG or larger power wire should terminate into a distribution block mounted as close to the amplifiers as possible and should connect to the J2-320.4 with 4 AWG power wire.

Note: Smaller AWG numbers mean bigger wire and vice-versa (1/0 AWG is the largest, 2 AWG is smaller, then 4 AWG, then 8 AWG, etc.).

To connect the power and ground wires to the amplifier, strip 1/2-inch (12 mm) of insulation from each wire and insert the bare wire into the the appropriate terminal block positions on the J2-320.4. Use a Phillips screwdriver to secure the wire via the screw on the top of each terminal.

The “GROUND” connection should be made using 4 AWG wire and should be kept as short as possible, while accessing a solid piece of sheet metal in the vehicle. The surface of the sheet metal should be sanded at the contact point

to create a clean, metal-to-metal connection between the chassis and the termination of the ground wire. The use of a star washer to lock down the connection is advisable.

Any wires run through metal barriers (such as firewalls), must be protected with a high quality insulating grommet to prevent damage to the insulation of the wire. Failure to do so may result in a dangerous short circuit.

Many vehicles employ small (10 AWG -

6 AWG) wire to ground the battery to the vehicle chassis and to connect the alternator’s positive connection to the battery. To prevent voltage drops, these wires should  be upgraded to 4 AWG when installing amplifier systems with main fuse ratings above 60A.

Fuse Requirements

While the J2-320.4 has two 30A ATC fuses

on its power connection panel, these do nothing to protect the vehicle from a dangerous short circuit in the power wire. They only protect the amplifier. It is absolutely vital that the main power lead to the amplifier(s) in the system be fused within 18 inches (45 cm) of the positive battery post connection. The fuse value at each power wire should be high enough for all of the equipment being run from that power wire.

If only the J2-320.4 is being run from that power wire, we recommend a 60A fuse be used. AFS or MAXI-type fuses are recommended.

R)	FUSES	+
	30A	30A

4 JL Audio

5