S T E P 4

Drill a 1/2” hole through the impression made in the 3” x 3” Wax Square in towards the rear wheel.

*CAUTION*

Before drilling, always make sure that you are not going to be drilling into any gas lines, brake lines, tires, transmission lines, electrical wiring, exhaust systems or anything else that might cause a reduction in your weekly pay. Always wear eye protection when drilling.

S T E P 5

Pull down the rear fender liner so that you have access to the hole drilled in STEP 4.

Place the Stealthbox® into place making sure that the speaker wire is properly attached to the enclosure and, that the 3/8- 16 x 2 1/4” Allen Head Set Screw comes through the hole Drilled in STEP 4.

S T E P 6

Using an Allen Wrench, back the 3/8-16 x 2 1/4” Allen Head Set Screw out of the Stealthbox® as shown, far enough so that the 3/8 x 1 1/4” Fender Washer, 3/8” Split Lock Washer and, 3/8-16 Hex Nut can be installed as shown in the DETAIL below. You may want to hold the Allen Head Set Screw using the Allen Wrench while tightening this hardware.

D E T A I L

The hardware discussed in STEP 6 is detailed here. Re-install the inner fender liner removed in STEP 5, put all of the stuff you took out of the trunk in STEP 1 back in.

C O N G R A T U L A T I O N S !

You have completed the installation for this model!

Enjoy your new Stealthbox®!

Please refer to the Power Recommendation section for an

amplifier recommendation and basic set-up help.

 

SB-D-CLGR/12W3v3 INSTR_SKU# 011294

I N C L U D E D H A R D W A R E

 

 

1) 3/8-16 x 2 1/4” Allen Head Set Screw

1) 3/8” Split Lock Washer

1) 3/8” x 1 1/4” Fender Washer

1) 3/8-16 Hex Nut

1) 3” x 3” Wax Square

 

 

S P E C I F I C A T I O N S

 

 

 

 

 

Enclosure Type: Acoustic Suspension (sealed)

 

 

Driver Type: 12W3v3-4

 

 

Nominal Impedance: 4Ohms

 

 

Continuous Power Handling: 500 Watts

 

 

P o w e r R e c o m m e n d a t i o n

 

 

 

 

 

JL Audio recommends using a high quality amplifier such as the JL Audio 250/1v2.

The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 250/1v2 when being used to power your Stealthbox®.

The JL Audio 250/1v2 is a very versatile audio component. Please consult the owner’s manual for even more detailed information about installing and tuning this amplifier.

M I D / H I G H F r e q u e n c y D r i v e r F I T M E N T

A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.

Front Speaker Size / Location: 3 1/2”- Dash / 6”x 9”- Front Doors

Fits JL Audio Models: TR350-Dash / TR690TXi-Doors

Rear Speaker Size / Location: 6 1/2”- Rear Deck

Fits JL Audio Models: TR650CXi, TR650CSi, C2-650x, C2-650, C5-650x, C5-650, ZR650CSi

(954) 443-1100

 

www.jlaudio.com

 

 

 

All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered

 

 

 

 

trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.

 

 

 

 

JLA-SKU# 011294 06-16-2009 • Printed in USA • ©2008 JL Audio, Inc. • U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902 #6,243,479

 

 

 

 

#6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign patents pending.

 

 

 

 

For more detailed information please visit us online at www.jlaudio.com.

 

 

 

 

 

 

1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y

M I R A M A R , F L O R I D A

3 3 0 2 5

U S A

Page 2 • JL Audio, Inc 2009

Page 2
Image 2
JL Audio SB-D-CLGR/12W3V3 warranty N G R a T U L a T I O N S, T a I L, C L U D E D H a R D W a R E, Specification S