Cont.
From
Previous
Page | STEALTHBOX WALL |
➔ ➔
FENDER WASHER
FLAT WASHER
LOCK WASHER
HEX NUT
THREADED INSERT
➔ | ➔ | CONGRATULATIONS! |
|
| INSTALL COMPLETE. |
VEHICLE SHEET METAL
SOCKET CUP SET SCREW
STEP 6: Run speaker wire to the/each enclosure and attach to the speaker terminal cup. Check the woofer(s) for proper operation at this time.
STEP 7: Back out the/each socket cup set screw | STEP 8: Lower the rear seat and replace all | Included Hardware: | |
to expose about | removed contents. | 1) 3” x 3’ wax Square | |
Place the socket cup set screw through the mount- |
| 1) | |
| 1) | 3/8” x | |
ing hole that was drilled, inside the truck. |
| ||
| 1) | 3/8” Flat Washer | |
From the under side of the truck, place a supplied |
| ||
| 1) | 3/8” Split Lock Washer | |
fender washer, flat washer, lock washer and then hex |
| ||
| 1) | 3/8” - 16 Hex Nut | |
|
| ||
nut onto the/each socket cup set screw. Secure tightly, using a 14mm socket and ratchet.
Difficulty Of Installation:
Specifications:
Enclosure Type: Ported
Driver Type:
Nominal Impedance: 2Ω | per woofer / can be rewired for 8Ω per woofer |
Cont. Power Handling: | 400Watts per woofer / 800Watts for system |
JL Audio recommends using a high quality amplifier such as the JL Audio 500/1 or the JL Audio 1000/1. The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for either the 500/1 or the 1000/1 when being used to power your Stealthbox®.
Preamp Output Section | Infrasonic Filter | "Q" | Center Freq. | Boost (dB) | Amp LP Filter | Amplifier Input Section | Subwoofer Output | |||
Output Mode | Filter Slope |
| 1.6 |
| 45 |
| +10 | Mode / Slope | Input Voltage Input Sens. Signal Sensing |
|
|
| 1.1 | 2.7 | 35 | 55 | +4 | +13 |
|
|
|
0.7 | 25 | 70 |
Full Range / Amp Filter / Out Filter | 12dB / 24dB | Off / 30Hz | 4.3 | 20 | 85 | 0 | Off / 12dB / 24dB | Low / High | Off / On |
|
| 0.5 | +15 |
|
|
+12VDC Ground Remote | 65 |
| Filter Mode |
| 30 | Bass EQ |
|
| 65 | + | + | _ | _ |
55 | 85 |
| 25 | 40 | Advanced | 55 | 85 | ||||||
| 45 | 120 |
| 18 | 50 |
| 45 | 120 |
|
| |||
JL AUDIO 500/1 |
|
|
|
|
|
| Bass |
|
|
|
|
|
|
40 | 200 | LP / HP | 15 | 60 | Off / On | Control | 40 | 200 | MONO OUTPUT ONLY | ||||
|
|
|
|
|
|
|
|
|
|
|
|
| |
Left Ch. | Right Ch. | Filter Freq. (Hz) | Infrasonic Freq. (Hz) | Remote Bass Port | Filter Freq. (Hz) | Left Ch. | Right Ch. |
The JL Audio 500/1 or the JL Audio 1000/1 is a very versatile audio component. Please consult the owner’s manual for detailed information about installing and tuning this amplifier.
Mid/High Frequency Driver Information:
Front Location Driver Size:
6.5” Separates
Applicable JL Audio Products:
TR,VR,XR &
Rear Location Driver Size:
4”x 6”
Applicable JL Audio Products:
TR400-CXi
10369 N. Commerce Pkwy, Miramar, Florida | Phone: 954.443.1100 Fax: 954.443.1111 |
w w w . j l a u d i o . c o m
SB - GM - SXT/10W6v2, JL AUDIO, Inc 2006 | Pag e 2 | Sheet SKU#011199 Revision 1/12/2006 |
