Jonsered 2159 manual Technical Data

TECHNICAL DATA

	2159
Engine
Cylinder volume, cu.in/cm3	3,6/59
Cylinder bore, inch/mm	1,85/47
Stroke, inch/mm	1,34/34
Idle speed, rpm	2 700
Power, kW/ rpm	3,0/ 9 000
Ignition system
Manufacture	FHP
Type of ignition system	ET
Spark plug	Champion RCJ 7Y
Electrode gap, inch/mm	0,2/0,5
Fuel and lubrication
system
Manufacturer	Walbro
Carburetor type	HDA 175
Fuel capacity, US pint/litre	1,27/0,7
Oil pump capacity at 8500 rpm,
ml/min	5-15
Oil capacity, US pint/litre	0,69/0,38
Type of oil pump	Automatic
Weight
Without bar and chain, Lbs/kg	12,4/5,6
	W: 12,6/5,7
	CAT: 12,4/5,6
	W CAT: 12,6/5,7
Chain/bar
Standard bar length,
inches/cm	15"/38
Recommended bar lengths,
inches/cm	13-20"/33-50
Usable cutting length,
inches/cm	12-19"/31-48
Chain speed at max.
power, m/sec	20
Pitch, inch/mm	0,325"/8,25
Thickness of drive link,	3/8"/9,52
	0,050"/1,3
inch/mm
	0,058"/1,5
Number of teeth on drive	0,063"/1,6
sprocket	7

34´*xo)¶5Y¨

– English

Recommended original and replacement bar and chain combinations

Following is a list of recommended cutting equipment for the Jonsered chain saw model 2159. The combinations of powerhead, bar and chain have been investigated in accordance with the kickback and vibration requirements of ANSI B 175.1 – 1991.

The guide bar nose radius is determined by either the maximum number of teeth in the nose sprocket or the corresponding maximum nose radius of a solid bar.

The following list is the chain saw manufacturers recommendations. There may be other combinations available, which will also achieve kickback reduction.

As we are listing the maximum guide bar nose radius, you may use a guide bar with smaller nose radius than in our list. For guide bars of the same length, all sprocket-nose guide bars of the same pitch and having the same number of of sprocket teeth may be conside- red to have equivalent kickback energy. A hard nose bar having the same length and nose radius as a sprocket-nose bar may be considered to have equivalent or less kickback energy than the sprocket-nose bar.

Low kickback saw chain is a chain which has only met the kickback performance requirements of ANSI B 175.1 safety requirements for gasoline-powered chain saws when tested on the representative sample of chain saws below 3.8 cu. in. specified in ANSI B 175.1. We recommend that you as replacement use the listed chains or "Low kickback saw chains" which are available at your dealer.

Guide bar			Saw chain
Length	Pitch	Max nose
inch	inch	radius

130,325" 10T Jonsered S25 or Oregon 20/21/22BP

150,325" 10T

160,325" 10T

180,325" 10T

150,325" 10T Total/Sabre 528PS, 520PS, 523PS

160,325" 10T

18 0,325" 10T

15	3/8"	11T	Jonsered S42 or Oregon 72/73/75LP
16	3/8"	11T
18	3/8"	11T
20	3/8"	11T
15	3/8"	11T	Total/Sabre 988PC, 980PC, 983PC
16	3/8"	11T
18	3/8"	11T
20	3/8"	11T

Note: For the chains above you are free to choose between 0,050", 0,058" and 0,063" gauge drive link for the corresponding bar, see table below.

0,050" (1,3 mm)	20BP	72LP	520PS	980PC
0,058" (1,5 mm)	S25/21BP	S42/73LP	528PS	988PC
0,063" (1,6 mm)	22BP	75LP	523PS	983PC