Manuals / Jonsered / Lawn and Garden / Brush Cutter

Jonsered GC2236 manual Cutting, Sweeping, Working Techniques

Models: GC2236

1 36

Download 36 pages 6.9 Kb

Page 21

Image 21

WORKING TECHNIQUES

Cutting

•The trimmer is ideal for cutting grass that is difﬁcult to reach using a normal lawn mower. Keep the cord parallel to the ground when cutting. Avoid pressing the trimmer head against the ground as this can ruin the lawn and damage the tool.

•Do not allow the trimmer head to constantly come into contact with the ground during normal cutting. Constant contact of this type can cause damage and wear to the trimmer head.

Sweeping

•The fan effect of the rotating cord can be used for quick and easy clearing up. Hold the cord parallel to and above the area to be swept and move the tool to and fro.

•When cutting and sweeping you should use full throttle to obtain the best results.

English – 21

Page 21

Image 21

Jonsered GC2236 manual Cutting, Sweeping, Working Techniques

Contents

English GC2236 Operator′s manualSymbols KEY TO SYMBOLSThe operator of the machine must ensure, while working, that noContents CONTENTSKEY TO SYMBOLS CONTENTSDear Customer INTRODUCTIONWhat is what on the brushcutter? WHAT IS WHAT?WARNING! Listen out for warning signals GENERAL SAFETY PRECAUTIONSPersonal protective equipment WARNING! The ignition system of thisThrottle lockout Machine′s safety equipmentWARNING! Never use a machine with GENERAL SAFETY PRECAUTIONSCutting attachment guard Stop switchVibration damping system WARNING! Never use a cuttingWARNING! Mufﬂers ﬁtted with catalytic MufﬂerRemember the risk of ﬁre WARNING! The inside of the mufﬂer WARNING! Bear in mind that TheCutting equipment WARNING! Using an incorrect cuttingLocking nut Cutting equipmentTrimmer head Sharpening grass cutters and grass bladesGeneral rules WARNING! Always discard a blade that isWARNING! When ﬁtting the cutting ASSEMBLYFitting the J-handle Assembling the cutting equipmentFitting a blade guard, grass blade and grass cutter Fitting the guard extensionGF E D A B C A ASSEMBLYFitting other guards and cutting attachments ASSEMBLYH BA M L WARNING! Take care when handling fuel Fuel safetyFUEL HANDLING FuelFuelling precautions, will lessen the risk of ﬁreMixing WARNING! The catalytic converterCheck before starting STARTING AND STOPPINGStarting and stopping StartingStopping WARNING! When the engine is startedstarter cord around your hand STARTING AND STOPPINGWORKING TECHNIQUES Basic safety rulesGeneral working instructions WARNING! Neither the operator of theBasic working techniques Grass clearing using a grass bladeGrass trimming with a trimmer head WARNING! Sometimes branches orCutting SweepingWORKING TECHNIQUES Basic setting MAINTENANCEFine adjustment Recommended max. speed See the Technical data sectionCorrectly adjusted carburettor Fine adjustment of the idle speed TLow speed jet L High speed jet HCooling system MufﬂerBevel gear Remember the risk of ﬁreAir ﬁlter Cleaning the air ﬁlterSpark plug Oiling the air ﬁlterMaintenance Maintenance schedulemaintenance DailyTechnical data TECHNICAL DATATechnical data WeightEC-declaration of conformity Approved accessoriesApplies to Europe only Type6 Nm Poly Trim20mm 20mm10 cm 4,2 m 8,5 mClic 15 cm095-.106 2,4-2,7mm4,25 m 4,25 m2,4-2,7 mm Tap n’ Go 35 Spin095-.106 8,5 m10 m Tap n’Go 45 Spin10 cm 4,3 m 15 cmPage Page ´z+S5¶64¨ 2008-05-30 ´z+S5¶64¨ 1151216-26