REMOTE CONTROL | (CONTINUED) |
REMOTE CONTROL BASICS
•Before you can operate the remote control, you must first install the batteries (included). See “Changing the Batteries” on this page above for instructions. (For an illustration, please see page 6.)
•Press the POWER button to turn the television on or off.
•Make sure the TV/CATV switch is set to TV. Move the switch to
CATV only if you need to operate a cable box.
•Slide the VCR/DVD selector switch to VCR to control a VCR, slide to DVD to control a DVD player. Please see pages 8 to 10 for instructions on programming your remote control to operate a Cable box, VCR or DVD player.
•Press the CH + and CH – buttons to scan through the channels. Tap the CH + or CH – button to move through the channels one channel at a time.
•Press VOL + or VOL – to raise or lower the volume. An indicator bar will appear onscreen to show you the television volume level.
•The CH +/– and VOL +/– buttons are also used to navigate JVC’s onscreen menu system.
•You can directly access specific channels using the
•This remote includes illuminated buttons for key features like CH +/– buttons, and VOL +/– buttons. Press the LIGHT button to turn the illumination on.
BATTERY PRECAUTIONS
The precautions below should be followed when using batteries in this device:
1.Use only the size and type of batteries specified.
2.Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. Reversed batteries may cause damage to the device. To avoid a potential short circuit, insert the
3.Do not mix different types of batteries together (e.g. Alkaline and
4.If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.
5.Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow battery manufacturer’s directions.)
6.When you change the batteries, try to complete the task within three minutes. If you take longer than three minutes, the remote control codes for your Cable Box may have to be reset (see page 8).
EFFECTIVE DISTANCE OF THE REMOTE CONTROL TRANSMITTER
CHANGING THE BATTERIES |
|
|
|
|
|
|
| |
Push down on the remote’s back cover and slide |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| ||
towards the bottom to remove it. |
|
|
|
|
|
|
| |
Insert two AA batteries (supplied), carefully noting the |
|
|
|
|
|
|
| |
“+” and |
|
|
|
|
|
|
| |
control. To avoid a potential short circuit, insert the |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| ||
end first. |
|
|
|
|
|
|
| |
Be sure to use only size AA batteries. |
|
|
|
|
|
|
| |
When batteries are installed, slide the cover back into |
|
|
| 15 FEET | ||||
place (until it clicks into position). |
|
|
| |||||
30˚ | 30˚ | |||||||
• If the remote control acts erratically, replace the | ||||||||
batteries. Typical battery life is six months to one year. |
|
|
|
|
|
|
| |
We recommend using alkaline batteries for longer |
|
|
|
|
|
|
| |
battery life. |
|
|
|
|
|
|
| |
When you change the batteries, try to complete the |
|
|
|
|
|
|
| |
task within three minutes. If you take longer than three |
|
|
|
|
|
|
| |
minutes, the remote control codes for your VCR, DVD, |
|
|
|
|
|
|
| |
and/or Cable Box may have to be reset (pages | NOTES: •When there is an obstacle between the TV | |||||||
| and the transmitter, the transmitter may not | |||||||
| operate. |
|
|
|
| |||
•When direct sunlight, an incandescent lamp, fluorescent lamp or any other strong light shines on the Remote sensor of the TV, the remote operation may be unstable.
7
