ELECTRICAL CONNECTIONS
To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all electrical connections before installing the receiver.
•Be sure to ground this receiver to the car’s chassis again after installation.
Notes:
• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio dealer.
• It is recommended to connect to the speakers with maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 Ω to 8 Ω). If the maximum power is less than 50 W, change “AMP GAIN” setting to prevent the speakers from being damaged (see page 21 of the INSTRUCTIONS).
• To prevent
Heat sink
• The heat sink becomes very hot after use. Be careful not to touch it when removing this receiver.
A Typical Connections
Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this receiver.
The leads of the power cord and those of the connector from the car body may be different in color.
1Connect the colored leads of the power cord in the order specified in the illustration below.
2Connect the antenna cord.
3Finally connect the wiring harness to the receiver.
|
|
| SUBWOOFER*3 |
|
| *3 Only for | |
|
| To CD changer or another external component (see diagram ) |
|
|
| ||
Rear ground |
|
|
|
|
|
|
|
terminal |
|
|
|
| *1 Not included for this receiver | Ignition switch | |
|
|
| 15 A fuse |
|
|
|
|
Antenna terminal | Line out (see diagram | ) |
|
|
|
|
|
|
|
| Black | To metallic body or chassis of the car |
|
| |
|
|
|
|
|
| ||
|
|
| Yellow*2 | To a live terminal in the fuse block connecting to the car battery |
| ||
|
|
|
| (bypassing the ignition switch) (constant 12 V) |
| ||
|
|
| Red | To an accessory terminal in the fuse block |
| ||
|
|
|
| Fuse block | |||
|
|
|
|
|
|
| |
|
|
| Blue | To the automatic antenna if any |
| ||
*2 Before checking the operation of this |
|
| (250 mA max.) |
|
|
| |
receiver prior to installation, this lead must | Blue with white stripe |
|
|
| |||
be connected, otherwise power cannot be |
| To the remote lead of other equipment (200 mA max.) |
| ||||
turned on. |
|
| Orange with white stripe |
|
|
| |
|
|
|
| To car light control switch |
| ||
|
|
|
|
|
|
| |
|
|
| Brown |
|
| To cellular phone | |
|
|
|
|
|
| ||
White with black stripe | White | Gray with black stripe | Gray | Green with black stripe | Green | Purple with black stripe | Purple |
Left speaker (front) | Right speaker (front) | Left speaker (rear) | Right speaker (rear) |
B Connecting the external amplifiers
You can connect amplifiers to upgrade your car stereo system.
•Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it can be controlled through this receiver.
•Disconnect the speakers from this receiver, connect them to the amplifier. Leave the speaker leads of this receiver unused.
Remote lead | |
| To the remote lead of other equipment or auto antenna if any |
Remote lead (Blue with white stripe)
Rear speakers
JVC Amplifier
Front speakers | Only for |
JVC Amplifier
Only for
JVC Amplifier
Subwoofer
Front speakers
*5 Signal cord (not supplied for this receiver)
*4 Firmly attach the ground wire to the metallic body or to the chassis of the
C Connecting the external components
CD changer
• Refer also to page 13 of the INSTRUCTIONS.
External component
• Set “EXT IN” to “EXT IN” (See page 21 of the INSTRUCTIONS.) |
JVC CD changer
*6 Connecting cord supplied for your CD changer
*7 Only for
CAUTION:
• Before connecting the CD changer, make sure that the receiver is turned off.
CD changer jack
External component
*8 Line Input Adapter
2
