PREPARATION

 

 

TROUBLESHOOTING

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

You need the installation kits which corresponds to your car.

 

 

• The fuse blows. ] Are the red and black leads connected correctly?

• Mark all the check boxes (

 

 

) to make sure you have follow the instructions and the listed parts.• Power cannot be turned on. ] Is the yellow lead connected?

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• No sound from the speakers. ] Is the speaker output lead short-circuited?
Check the battery system in your carPrepare this before installation

• Sound is distorted. ] Is the speaker output lead grounded? ; Are the “–” terminals of L and R speakers grounded in

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

common?

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12 V DC, NEGATIVE ground

 

 

• Noise interfere with sounds. ] Is the rear ground terminal connected to the car’s chassis using shorter and thicker

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

cords?

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• This unit becomes hot. ] Is the speaker output lead grounded? ; Are the “–” terminals of L and R speakers

grounded in common?
• This unit does not work at all. ] Have you reset your unit?
Parts list for installation and connection
AControl panel

 

BSleeve

 

CTrim plate

 

DPower cord

 

EHandles

 

FRemote controller / Battery

INSTALLATION

The following illustration shows a typical installation. If you are not sure how to install this unit correctly, contact your JVC car audio dealer or a company supplying kits.

INSTALLATION / CONNECTION

In-dash mounting
See “ELECTRICAL
CONNCECTIONS” below.
When installing the unit without using the sleeve

In a Toyota car for example, first remove the car radio and install the unit in its place.

 

8 mm (3/8")
Pocket

Flat head screws—M5 × 8 mm (3/8")*2

 

Bracket*2
Removing the unit
Release the rear section first...

ELECTRICAL CONNECTIONS

Make sure to disconnect the battery’s negative terminal.

 

• Be sure to ground this unit to the car’s chassis again after installation.
High
Note:

 

It is recommended to connect to the speakers with maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 Ω to 8 Ω). If the

maximum power is less than 50 W, change “AMP GAIN” setting to prevent the speakers from being damaged (see “General settings—PSM”).

Heat sink

Typical connections
Connecting the external amplifier or subwoofer
Rear line out
Rear ground terminal

 

Antenna

 

15 A fuse
terminal

 

 

 

 

 

 

 

Ignition switch

 

 

Black
To the metallic body
Connect only the front speakers if your
or chassis of the car
speaker system is two-speaker system.

 

White with black stripe
To a live terminal in the
fuse block connecting to the

 

 

Yellow *3

 

 

 

car battery (bypassing the
Front speaker (left)
White

 

ignition switch) (constant

 

12 V)

 

 

 

Gray with black stripe
Fuse block

 

 

 

Red
To an accessory terminal in
Set “L/O MODE” to “REAR”(See “General settings—PSM.”)
You can connect a power amplifier for rear speakers.
Rear
JVC Amplifier
speakers

 

Set “L/O MODE” to “WOOFER” (See “General settings—PSM.”)You can also connect a subwoofer to the REAR LINE OUT terminals.
Remote lead

Y-connector *2

Remote lead (blue with white stripe)

To the remote lead of other equipment or automatic antenna if any

Signal cord*2
Right
Left

Front speakers

Front speaker (right)
Gray

 

the fuse block

 

 

Green with black stripe

Blue with white

To the remote lead of other

 

 

stripe

 

 

equipment or automatic antenna if

 

 

 

JVC Amplifier
Subwoofer

or

Rear speaker (left)
Green

any (200 mA max.)

 

Purple with black stripe

 

Rear speaker (right)
Purple

 

PRECAUTIONS on power supply and speaker connections

IMPORTANT: A custom wiring harness (separately purchased)

*1

When you stand the unit, be careful not to damage the fuse on the rear.

which is suitable for your car is recommended for connection

*2

Not supplied for this unit.
between the unit and your car.

*3

Before checking the operation of this unit prior to installation, this lead must be connected, otherwise the power cannot be

• Consult your JVC car audio dealer or a company supplying

 

turned on.
kits for details.

*4

Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place uncoated with paint (if coated

 

with paint, remove the paint before attaching the wire). Failure to do so may cause damage to the unit.

4– EN