CD RECEIVER : INSTRUCTIONS/INSTALLATION
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best possible performance from the unit.
For customer Use:Enter below the Model No. and Serial No. which are located on the top or bottom of the cabinet. Retain this information for future reference.
Model No.
Serial No.
0710DTSMDTJEIN |
|
EN | |
© 2010 Victor Company of Japan, Limited | [J] |
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
Caution:Changes or modifications not approved by JVC could void the user’s authority to operate the equipment.
IMPORTANT FOR LASER PRODUCTS1.CLASS 1 LASER PRODUCT
2.CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel.
3.CAUTION: (For U.S.A.) | Visible and/or invisible class II laser radiation when open. Do not stare into beam. |
(For Canada) | Visible and/or invisible class 1M laser radiation when open. Do not view directly |
| with optical instruments. |
4.REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.
Canceling the display demonstration 
1 | Turn on the power. | 4 | Select <DEMO OFF>. |
2 | [Hold] | 5 |
|
|
| ||
3 | (Initial setting) |
|
|
| 6 | Finish the procedure. | |
|
|
| For safety... | |
[European Union only] | • Do not raise the volume level too much, as this will | |
block outside sounds, making driving dangerous. | ||
| ||
| • Stop the car before performing any complicated | |
| operations. |
| Warning: | Temperature inside the car... |
If you need to operate the unit while driving, be sure | If you have parked the car for a long time in hot or |
to look around carefully or you may be involved in a | cold weather, wait until the temperature in the car |
traffic accident. | becomes normal before operating the unit. |
Setting the clock 
Basic operations 
1 | Turn on the power. | 5 |
2 | [Hold] | 6 |
|
|
(Initial setting)
3Select <CLOCK>.Ejects the disc | Control dial | Loading slot | Display window | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Detaches the panel | Auxiliary input jack |
Returns to the previous menu
4 Select <CLOCK SET>.Remote sensor
• DO NOT expose to bright sunlight.
Preparations
How to attach/detach the control panel
How to reset your unit
Reset the unit after installation is completed.
• Your preset adjustments will also be erased.
How to forcibly eject a disc
[Hold]
•You can forcibly eject the loaded disc even if the disc is locked. To lock/unlock the disc, see page 2.
•Be careful not to drop the disc when it ejects.
•If this does not work, reset your unit.
Preparing the remote controller
If the effectiveness of the remote controller decreases, replace the battery.
Replacing the lithium coin batteryCR2025
For
This product contains a CR Coin Cell Lithium Battery which contains Perchlorate
See www.dtsc.ca.gov/hazardouswaste/perchlorate
Caution:
•Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
•Battery shall not be exposed to excessive heat such as sunshine, fire, or the like.
Warning (about battery handling)To prevent accidents and damage:
USB (Universal Serial
Bus) input jack
When you press or hold the following button(s)...
RemoteMain unitGeneral operations controllerTurns on.
•When the power is on, pressing 
/I/ATT on the remote controller also attenuates the sound or pauses. Press 
/I/ATT again to cancel
|
|
|
|
|
|
|
| muting or resume playback. |
|
|
|
|
|
|
|
| Turns off if pressed and held. |
|
|
|
|
|
|
|
| Selects the available sources (if the power is turned on). |
|
|
|
|
|
|
|
| • If the source is ready, playback also starts. |
|
|
|
|
|
|
|
| Adjusts the volume level. |
|
|
|
|
|
|
|
|
|
|
| — | Selects items. | |||||
|
|
|
|
|
|
|
| • Mutes the sound while listening to a source. If the source is “CD” or |
|
| — | “USB,” playback pauses. Press the control dial again to cancel muting | |||||
|
| or resume playback. | ||||||
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| • Confirms selection. |
Selects the sound mode.
• Enters tone level adjustment directly (see page 3) if pressed and held EQ
— Enters playback mode menu directly (see page 2).
(RM-RK50)
When you use the remote controller for the first time, pull out the insulation sheet.
•Do not install any battery other than CR2025 or its equivalent.
•Store out of reach of children.
•Do not recharge, short, or dismantle.
•Do not dispose of in fire.
•Do not carry around with other metallic materials.
•Wrap the battery with tape and insulate when throwing away or saving it.
—
Power off : Checks the current clock time.
Power on : Changes the display information.
Insulation sheet 
1 – EN