
18 EN VIDEO PLAYBACK |
|
|
|
|
| |||
Shuttle Search |
| Connections To A TV Or VCR | ||||||
Allows | ||||||||
|
|
|
|
| ||||
playback. |
|
|
|
|
|
|
| |
1) During playback, press 5 for forward search, or |
|
|
|
|
| |||
3 for reverse search. |
|
|
| To AV connector | ||||
2) To resume normal playback, press 4/9. | Open the cover. |
|
|
| ||||
● During playback, press and hold 5 or 3. The search |
|
|
| |||||
S/AV/Editing cable |
|
| ||||||
continues as long as you hold the button. Once you release |
| mark | ||||||
the button, normal playback resumes. |
| (provided) |
|
| ||||
● A slight mosaic effect appears on the display during Shuttle |
|
|
|
|
| |||
Search. This is not a malfunction. |
|
|
|
|
| |||
ATTENTION: |
|
|
|
|
|
| ||
During Shuttle Search, parts of the | 1 | 2 | 3 | 4 | 5 | |||
picture may not be clearly visible, | ||||||||
|
|
|
|
| ||||
particularly on the left side of the |
|
|
|
|
| |||
screen. |
|
|
|
|
|
|
| |
Blank Search |
|
| “Y/C”/“CVBS” |
| Cable Adapter* | |||
| Video Out Select |
|
| |||||
Helps you find where you should start recording in the |
| Switch |
|
| ||||
|
|
|
|
| ||||
middle of a tape to avoid time code interruption. |
| To TV or VCR |
|
| ||||
|
|
|
|
| ||||
|
|
|
|
|
|
| ||
|
|
|
| TV | ||||
2 Set the VIDEO/MEMORY Switch to “VIDEO”. |
|
|
|
|
| |||
3 Set the Power Switch to “PLAY” while pressing down |
|
| VCR |
| ||||
the Lock Button located on the switch. |
|
|
| |||||
|
|
|
|
| ||||
4 Press MENU. The Menu Screen appears. | A Not connected |
|
|
| ||||
5 Press | or | to select “t”, and press SET. The |
|
|
| |||
B Black to | ||||||||
VIDEO Menu appears. | ||||||||
6 Press | or | to select “BLANK SRCH”, and press | is not necessary to connect the yellow video cable.) | |||||
SET. The Sub Menu appears. | C Yellow to VIDEO IN (Connect when your TV/VCR has | |||||||
7 Press | or | to select “EXECUTE”, and press SET. | only A/V input connectors.) |
| ||||
D Red to AUDIO R IN** |
|
| ||||||
● The “BLANK SEARCH” indication appears and the | E White to AUDIO L IN** |
|
| |||||
camcorder automatically starts reverse or forward search, |
|
| ||||||
then stops at the spot which is about 3 seconds of tape | * If your VCR has a SCART connector, use the provided | |||||||
cable adapter. |
|
|
| |||||
before the beginning of the detected blank portion. |
|
|
| |||||
** Not required for watching still images only. | ||||||||
● To cancel Blank Search midway, press 8. |
NOTES:
●Before starting Blank Search, if the current position is at a blank portion, the camcorder searches in the reverse direction. If the current position is at a recorded portion, the camcorder searches in the forward direction.
●If the beginning or end of the tape is reached during Blank Search, the camcorder stops automatically.
●A blank portion which is shorter than 5 seconds of tape may not be detected.
●The detected blank portion may be located between recorded scenes. Before you start recording, make sure there is no recorded scene after the blank portion.
NOTE:
Set the video out select switch of the cable adapter as required:
Y/C: When connecting to a TV or VCR which accepts Y/C signals and uses an
CVBS: When connecting to a TV or VCR which does not accept Y/C signals and uses an audio/video cable.
1 Make sure all units are turned off.
2 Connect the camcorder to a TV or VCR as shown in the illustration.
If using a VCR, go to step 3. If not, go to step 4.
3 Connect the VCR output to the TV input, referring to your VCR’s instruction manual.
4
5 Set the VCR to its AUX input mode, and set the TV to its VIDEO mode.