JVC HR-J7020UM specifications Other Functions, Checking tape position, Function settings

Other Functions

Checking tape position

When you change the VCR operation mode from the stop mode to fast forward or rewind mode, or when you perform an Index Search or Instant Review, the tape

position indicator appears.	B	+	+	+		E
The position of “q” in relation to “B”			COUNT		1:23:45
(Beginning) or “E” (End) shows you where
you are on the tape.

●Set “SUPERIMPOSE” to “ON”.( pg. 14)

Changing display information

Each time you press DISPLAY, the display panel shows the channel number and the clock time alternatively. ● You can change display in the stop, recording or

during rewind/fast-forward. ● When “SUPERIMPOSE” is set to “ON”

( pg. 14) and DISPLAY on the Remote is pressed, time counter will appear on the TV screen. To reset the time counter, press C. RESET on the Remote.

Function settings

You can use the other useful function settings on the Function Set screen.

Turn on the VCR and TV, and select the VCR channel (or AV mode).

A Access Main Menu screen, then	MAIN MENU
Function Set screen
	TUNER SET
	FUNCTION SET
Press MENU on the Remote. Press rtto	INITIAL SET
move the highlight bar (arrow) to
“FUNCTION SET”, then press OK or e.
	PRESS ( , ), THEN (OK)
B Select Function	PRESS (MENU) TO END

Press rtto move the highlight bar (arrow) to the function you want to set.

FUNCTION		PREVIOUS PAGE
B.E.S.T.	ON	BLUE BACK	ON
PICTURE CONTROL	AUTO	2ND AUDIO RECORD	OFF
AUTO TIMER	OFF	AUDIO MONITOR	HI-FI
SUPERIMPOSE	ON	AUTO POWER OFF	OFF
AUTO SP EP TIMER	OFF
VIDEO STABILIZER	OFF
NEXT PAGE
SELECT WITH ( , ) AND (OK)		SELECT WITH ( , ) AND (OK)
PRESS (MENU) TO END		PRESS (MENU) TO END

CChange setting

Press OK or e. The default setting is bold in the following table. Press MENU to return to normal screen.

Timer warning display

A warning appears on the TV screen to tell you that the timer-recording is to start in 5 minutes if you are not in the timer recording standby mode at that time. Press TIMER to put the VCR into timer recording standby mode. To clear the display, press CANCEL on the Remote.

–WARNING–

TIMER RECORDING TO START SOON

(CANCEL)

B.E.S.T. — ON/OFF

When B.E.S.T. (Biconditional Equalised Signal Tracking) system is set to “ON”, the recorder checks the condition of the tape in use during playback and recording, and compensates to provide the highest-possible pictures. B.E.S.T. takes place whenever you play back a tape or start recording after inserting a cassette.

NOTE:

The recorder checks the tape condition for about 7 seconds, then starts recording. To make sure you record the desired scene or programme completely, perform the following steps:

APress and hold 9, and press 7. After about 7 seconds, the recorder re-enters Record Pause mode.

B Press 4 to start recording.

PICTURE CONTROL — AUTO(NORM)/EDIT/SOFT/SHARP

This function helps you to adjust the playback picture quality according to your preference.

AUTO(NORM): Normally select this. Picture quality is adjusted automatically. When B.E.S.T. is set to “OFF”, the Picture Control will display “NORM”.

EDIT: Minimizes picture degradation during editing (recording and playback).

SOFT: Reduces image coarseness when viewing overplayed tapes containing much noise.

SHARP: Clearer, sharper-edged picture when viewing images with much flat, same-colored surfaces such as cartoons.

NOTE:

Select “EDIT” when you are editing tapes. After you finish editing the tapes, select “NORM”.

AUTO TIMER — ON/OFF

●When this function is set to “ON”:

The timer recording standby mode is automatically engaged when the VCR is turned off. It is temporarily canceled when the VCR is turned on. You do not have to press TIMER to engage or disengage the timer recording standby mode.

●When this function is set to “OFF”:

You have to press TIMER to engage or disengage the timer recording standby mode.

— 13 —