JVC HR-S5911U Multi-Brand Remote Control, Changing Remote Control Code, TV Brand Setting

Multi-Brand Remote Control

This Remote can control some functions of remote controllable TVs, cable boxes or DBS (Direct Broadcast Satellite) receivers listed below. Without setting, you can control a JVC TV.

NOTES:

●Some unit’s brands have more than one code. If the unit does not function with a specified code, try other codes.

●Depending on the type of unit, some or all functions cannot be operated using this Remote.

●It is not possible to operate a unit not equipped with a remote sensor.

●It is not possible to set the Remote for both your cable box and a DBS receiver at the same time.

●Once you have set the Remote to operate the unit, you do not have to set it until you replace the batteries from the Remote.

●If the batteries of the Remote are discharged, the Remote may not be able to control the TV, cable box or DBS receiver. Replace the batteries.

TV Brand Setting

ATurn on TV

Turn on the TV using the Power button on the TV or its Remote.

BSet TV brand code

APress and hold TV.

BPress MBR SET.

CPress the Number keys to enter your TV’s brand code.

DPress OK, and release TV. The TV should turn off.

COperate TV

While holding down TV, press one of the following buttons: POWER 1, TV/VCR, TV CH+/–, ^ (TV Muting), TV VOL+/–, and the Number keys.

●For some brands, you must press ENTER after having pressed the Number keys to enter a channel number.

TV BRAND	CODE	TV BRAND	CODE
JVC	01, 03	SONY	07
HITACHI	10	SAMSUNG	12
MAGNAVOX	02	SANYO	13
MITSUBISHI	03	SEARS	13
PANASONIC	04, 11	TOSHIBA	08
RCA	05	ZENITH	09
SHARP	06

Cable Box or DBS Receiver Brand Setting

ATurn on cable box or DBS receiver

Turn on the cable box or DBS receiver using the Power button on the unit or its Remote.

BEnter brand code

APress and hold CABLE/DBS.

BPress MBR SET.

CPress the Number keys to enter your cable box’s (or DBS receiver’s) brand code.

DPress OK, and release CABLE/DBS.

COperate cable box or DBS receiver

While holding down CABLE/DBS, press one of the following buttons: POWER 1, TV CH+/–, and the Number keys.

●For some brands, you must press ENTER after having pressed the Number keys to enter a channel number.

●To change the cable box’s (or DBS receiver’s) channels, press TV CH+/– or the Number keys. (The CH+/– button can be used to change the VCR’s channels only.)

CABLE BOX BRAND	CODE
ARCHER	01, 05, 17
CABLETENNA	01, 17
CABLEVIEW	15, 16, 17, 21, 25
CITIZEN	15, 16, 17, 21, 25
CURTIS	02
DIAMOND	01, 17
GC BRAND	15, 16, 17, 21, 25
GEMINI	15
GENERAL INSTRUMENTS	01, 04, 06, 11, 12, 15, 28
HAMLIN	10, 18, 23
JASCO	15
JERROLD	01, 04, 06, 11, 12, 15, 28
NOVAVISION	02
OAK	07
PANASONIC	13, 14
PULSER	15, 16, 17, 21, 25
RCA	13, 14
REGAL	10, 18, 23
REMBRANDT	01, 16, 17
SAMSUNG	05, 16, 24
SCIENTIFIC ATLANTA	02
SIGMA	07
SL MARX	05, 16, 17, 24, 25
SPRUCER	13, 14
STARGATE	05, 15, 16, 17, 21, 24, 25
TELEVIEW	05, 16, 24
TOCOM	01, 04, 16
UNIKA	01, 17
UNIVERSAL	16, 17, 25
VIDEOWAY	03, 09, 22
ZENITH	03, 09, 22
DBS RECEIVER BRAND	CODE
JVC (DISH Network)	51
ECHOSTAR (DISH Network)	51
SONY (DSS)	41
RCA (DSS)	40

Changing Remote Control Code

This Remote is capable of transmitting two control codes; one set to respond to A code control signals and another set to respond to B code control signals. This Remote control is preset to send A code signals because your VCR is initially set to respond to A code signals. You can easily modify your VCR and the Remote to respond to B code signals. When using two JVC VCRs, set two VCRs and their Remotes to different codes, so that you can operate these VCRs separately.

ASet remote control code for Remote

APress and hold A/B.

BPress the Number key “2”.

CPress OK, and release A/B.

●The Remote now can transmit B code control signals.

BCheck remote control code for VCR

Press and hold 4 on the VCR for more than 5 seconds while the VCR is turned off. The code currently set appears on the display panel.

CChange code for VCR

Press any key on the Remote. The VCR now responds to B code control signals.

●To set the Remote and the VCR back to A code control signals, repeat the same procedure as shown above except pressing the Number key “1” in step B of 1.

To control two VCRs with the same Remote

You can control two JVC VCRs by switching the remote control code for the Remote between A and B ( step A), keeping two VCRs to different control codes.

●To change only the remote control code for the Remote, DO NOT perform steps B and C.

— 17 —