AUTO POWER OFF — 3H / OFF

When this function is set to “3H”, the recorder turns off automatically if no operation is done in 3 hours. “AUTO POWER OFF IN 3MIN” appears on the screen 3 minutes before the recorder is turned off.

Clock Set

Turn on the recorder and the TV, and set your TV to its AV mode or video channel.

AAccess Main Menu screen, then Initial Set screen

Press MENU. Press rt to place the pointer next to “INITIAL SET”, then press OK or e.

BAccess Clock Set screen

Press rt to place the pointer next to “CLOCK SET”, then press OK or e.

C Set time, date and year

Press rt until the desired time appears, then press OK or e. Set the date and year in the same way.

●Holding rt changes the time in

30-minute intervals, or changes the date

in 15-day intervals.

DSet Just Clock

Set to “ON” or “OFF” by pressing rt, then press OK or e.

Just Clock

The Just Clock function provides accurate time keeping through automatic adjustments at regular intervals, by reading data from a PDC signal. Normally, set “JUST CLOCK” to “ON”.

NOTES:

●Just Clock may not function properly depending on the reception condition.

●When you select a country in Central or Eastern Europe for country setting, you cannot use Just Clock. Skip steps 4 – 5.

●Just Clock is not effective when …

…the recorder’s power is on.

…the recorder is in the Timer mode.

…a difference of more than 3 minutes exists beween the built- in clock’s time and the actual time.

…the recorder is in the Power Save mode ( 12).

…“L-2 SELECT” is set to “SAT” ( 12).

ESet source channel position

The recorder is preset to receive clock setting and adjustment data from channel position 1. Press rt to set the channel position to the number representing the station transmitting clock setting data, then press OK or e.

FStart clock

Press MENU.

ATTENTION:

If the AC was disconnected from the recorder and the recorder’s memory backup has expired, the recorder will automatically perform Auto Clock Set when the power is restored.

Tuner Set

Perform the following steps only if the tuner has not been set correctly by Auto Set Up or Preset Download, or if you have moved to a different area, or if a new station starts broadcasting in your area.

The recorder needs to memorise all necessary stations in channel positions in order to record TV programmes. Auto Channel Set automatically assigns all receivable stations in your area.

Auto Channel Set

AAccess Main Menu screen, then Auto Channel Set screen

Press MENU. Press rt to place the pointer next to “AUTO CH SET”, then press OK or e.

BSelect your country

Press rtto place the pointer next to your country, then press OK or e.

CSelect language

Press rt to place the pointer next to the desired language.

D Perform Auto Channel Set

Press OK twice. When Auto Channel Set is completed, “SCAN COMPLETED” is displayed on the screen for about 5 seconds, then the Confirmation screen appears.

● When you select a country in Central or

Eastern Europe for country setting, station names (ID) are not stored automatically. Change station names manually. ( 14)

EReturn to normal screen

Press MENU.

NOTES:

●Depending on reception conditions, the stations may not be stored in order, and the station names may not be stored correctly.

●If no sound accompanies the picture or the audio sounds unnatural on some channels, select the appropriate TV system for those channels.

●To delete stations with poor reception condition, refer to “Deleting a channel” ( 14).

Manual Channel Set

Store channels that were not stored during Auto Set Up, Preset Download or Auto Channel Set.

AAccess Main Menu screen, then Confirmation screen

Press MENU. Press rt to place the pointer next to “MANUAL CH SET”, then press OK or e.

B Select position

Press rt w e until an open channel position begins blinking, then press OK. The Manual Channel Set screen appears.

C Select band

Press rt to select CH (regular) or CC (cable), then press e.

DInput channel

Press the number keys to input the channel number you want to store. Input “0” before any single number entries.

● To input the registered station name (ID), press e until “– – – –” begins blinking, then press rt.

●When “L-2 SELECT” is set to “A/V” or “SAT”, the “DECODER” setting cannot be changed. ( 12)

●If you have selected a country in Central

or Eastern Europe for country setting,

“TV SYSTEM” setting appears instead of “DECODER” setting. When you can see the picture but can hear no audio, select appropriate TV system.

Press euntil D/K or B/G blinks. Then press rt to select D/K or B/G.

— 13 —