Step2:
Mounting this unit onto TK-C215VP series
Step6: Installing the dome cover
1.Install TK-C215VP series on [to HEATER] terminal the ceiling

Refer to TK-C215VP series “INSTRUCTIONS” for the installation method.

2. Mounting this unit onto Space for Heater of TK-C215VP series

• Mount this unit onto DOME CAMERA as

 

HEATER fastening

 

hole

shown in the right figure.

 

 

Insert the claw of this unit into Space for

 

 

Heater. Make sure to mount properly.

Space for Heater

 

• After inserting this unit into Space for Heater,

 

 

 

make sure to tighten the fastening screw of

 

 

this unit with a + screwdriver.

HEATER fas-

[to HEATER]

 

terminal

1.Cleaning the dome cover

Before mounting, remove any dust or dirt from the dome cover.

Memo

Dirt that is not removed from the cover before mounting may appear on the cam- era’s image.

Do not apply excessive force to the dome cover such as stretching it.

2.Mounting the dome cover to the base

Mount the dome cover by aligning the 3 position marks on the base with the dome cover.

Position Alignment Mark (x 3)

3 2

Wrench (Supplied)

3. Connecting cable

tening hole

3.

Cable

Connect the cable to the [to HEATER] terminal of

TK-C215VP series.

Space for Heater

Note

When mounting the dome cover, take note TK-C215VP4 is used in the illustration.

that the desiccant is not caught between base and dome cover.

3.Fastening the dome cover

Fasten by tightening the 3 fastening screws of the dome cover using the wrench supplied.

Claw

Cable

2.

Fastening Screws

TK-C215VP4 is used in the illustration.

Step7: Check items after installation

Check the following items after installation.

Is the power supply for TK-C215VP series AC 24 V?

Have you inserted the desiccant that comes with this unit?

Does an image appear normally on the monitor after switching on the power for TK-C215VP series?

Is the cable of this unit connected to the [to HEATER] terminal of TK-C215VP series?

Has the fastening screw of this unit been tightened properly?

Step3:

Adjust the field of view and lens of the camera

Specifications

Switch on the power supply of the camera.

Refer to TK-C215VP series “INSTRUCTIONS” on how to adjust the field of view and lens of the camera.

After adjusting the field of view and lens of the camera, switch off the power supply of the camera.

Step4: Install the inner dome

Mount the inner dome to the 3 lugs.

Note

Power supply / Voltage Power consumption Heater operationMassAccessories

AC 24 V ± 10%, 60 Hz/50 Hz

18 W (during AC 24 V)

Surrounding temperature -22 °F to 32°F ( -30fto 0f)(auto on/off)

*By using this unit, the operation guarantee temperature of the camera becomes -22 °F to 122°F (-30fto 50f)

56 g

 

Instructions ..........................................

1

Warranty Card .....................................

1

Service Information Card ....................

1

Desiccant ............................................

1

(Service Parts No.LW40790-001A)

 

Mount the inner dome such that it does

Lug(x 3)

not cover the lens.

 

When mounting the inner dome, make sure not to move the position of the lens. Doing so may cause the preset angle of view to go out of alignment.

Inner

Dome

TK-C215VP4 is used in the illustration.

Step5: Inserting the Desiccant supplied
o Dimensions(Unit: mm)

52

8145.5

* Design and specifications are subject to change without notice.

Take out the desiccant from the aluminum package, insert it into the desiccant insertion space of the camera unit and fasten using the lug plate.

Memo

During reconnection or re-installation after repair or maintenance, make sure to replace the desiccant with a new one.

Consult your nearby JVC’s dealer on the replacement procedures.

Serial number of part to be replaced: Use a LW40790-001A desiccant.

Desiccant Insertion Space

Attention:
Information for Users on Disposal of Old Equipment [European Union]

This symbol indicates that the electrical and electronic equipment should not be disposed as general household waste at its end-of-life. Instead, the product should be handed over to the applicable collection point for the recycling of electrical and electronic equipment for proper treatment, recovery and recycling in accordance with your national legislation.

By disposing of this product correctly, you will help to conserve natural resources and will help prevent potential negative effects on the environment and human health which could otherwise be caused by inappropriate waste handling of this product. For more information about collection point and recycling of this product, please contact your local municipal office, your household waste disposal service or the shop where you purchased the product.

Penalties may be applicable for incorrect disposal of this waste, in accordance

Note

When mounting is performed on a rainy day, make sure that rain water does not enter this unit.

Make sure to use the desiccant supplied. Failure to do so may cause the camera lens and dome cover to fog.

If the angle of view is not adjusted imme- diately after mounting the camera, insert the desiccant after adjustment is com- pleted. The desiccant loses its effect if it is exposed to the air for a prolonged period of time.

Desiccant

Lug Plate

TK-C215VP4 is used in the illustration.

This symbol is

only valid in the

European Union.

with national legislation.

(Business users)

If you wish to dispose of this product, please visit our web page www.jvc-europe.com to obtain information about the take-back of the product.

[Other Countries outside the European Union]

If you wish to dispose of this product, please do so in accordance with

applicable national legislation or other rules in your country for the treatment of old electrical and electronic equipment.

© 2006 Victor Company of Japan, Limited

LST0472-001A