Parts list for installation and connection
A | B | C | D | E |
| Control panel | Sleeve | Trim plate | Power cord | Washer (ø5) |
| G |
|
|
|
|
F | Mounting bolt— | H | I | J | K |
| Lock nut (M5) | M4 x 5 mm (M4 x 1/4"); | Rubber cushion | Handles | Remote controller | Battery |
| M5 x 15 mm (M5 x 5/8") |
|
|
|
|
INSTALLATION
The following illustration shows a typical installation. If you have any questions or require information regarding installation kits, consult your JVC car audio dealer or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
In |
| Removing the unit |
|
|
|
When you stand the unit, be careful not to damage
the fuse on the rear.Do the required electrical connections.Bend the appropriate tabs to hold the sleeve firmly in place.When using the optional stay
| Fire wall | Stay (option) |
When installing the unit without using the sleeve
In a Toyota car for example, first remove the car radio and install the unit in its place. |
|
| Flat type | * Not supplied for this unit. |
| Bracket* |
|
| Flat type screws |
|
| |
| |
Bracket* |
|
ELECTRICAL CONNECTIONS
Typical connections
Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this unit. The leads of the power cord and those of the connector from the car body may be different in color.
1Connect the colored leads of the power cord in the order specified in the illustration below.
2Connect the antenna cord.3Finally connect the wiring harness to the unit.| Line out | Rear ground terminal | |
| Antenna | 15 A fuse | |
| terminal | ||
|
| Connect only the front speakers if your | Black | To the metallic body | ||
| or chassis of the car | |||
| speaker system is |
|
| ||
| White with black stripe |
| To a live terminal in the | ||
| Yellow *2 | fuse block connecting to the | |||
|
| |||
|
|
| car battery (bypassing the | |
| Front speaker (left) | White |
| ignition switch) (constant | |
| 12 V) | |||
|
|
| ||
| Gray with black stripe |
| Fuse block | ||
| Red | To an accessory terminal in | |||
|
| |||
| Front speaker (right) | Gray |
| the fuse block | |
|
| |||
| Green with black stripe | Blue with white | |||
| stripe | To the remote lead of other | |||
|
| |||
|
| equipment or automatic antenna if | ||
|
|
| ||
| Rear speaker (left) | Green |
| any (200 mA max.) | |
|
| |||
Connecting the external amplifier or subwoofer
|
| Remote lead | |
| Set “L/O MODE” to “REAR” |
| Remote lead (blue with white stripe) | |
|
|
| |
| (See “General |
|
| To the remote lead of other equipment |
You can connect a power amplifier for |
|
| |
|
| or automatic antenna if any | |
| rear speakers. |
|
| |
|
|
| |
| JVC Amplifier |
|
|
|
| Rear |
|
|
|
| speakers |
|
|
|
|
|
| Front speakers |
| Set “L/O MODE” to “WOOFER” |
|
|
|
(See “General |
|
|
|
You can also connect a subwoofer to | *1 | Not supplied for this unit. |
|
| the REAR LINE OUT terminals. |
| ||
| *2 | Before checking the operation of this unit prior to installation, this | |
|
| lead must be connected, otherwise the power cannot be turned on. | |
| *3 | Firmly attach the ground wire to the metallic body or to the chassis | |
JVC Amplifier | or | of the | |
| |||
| remove the paint before attaching the wire). Failure to do so may | ||
| Subwoofer |
| ||
| cause damage to the unit. |
| |
|
|
| |
| *4 | Signal cord (not supplied for this unit) | |
PRECAUTIONS on power supply and speaker connections:
•DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit will be seriously damaged.
•BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in your car.
| Rear speaker (right) | Purple |