JVC KD-G498 guide

µËÕ≈«¥ “¬¥‘π„ÀÈ·πËπ‡¢È“°∫µ—«∂—ß‡À≈Á°—À√◊Õµ«∂—ß√∂—

∑’Ë‰¡Ë¡’‡§≈◊Õ∫’ (À“°¡’‡§≈◊Õ∫Õ¬ŸË’ „ÀÈ¢Ÿ¥ ÕÕ°°ËÕπ’ °ËÕπµËÕ≈«¥ “¬¥‘π) À“°‰¡ËªØ‘∫µ‘µ“¡§”·π—–π”π’È ‡§√◊ËÕßÕ“®™”√ÿ¥À√◊Õ‡ ¬À“¬‰’ ¥

µ√ß «πË

Heat sink

·ºËπ√–∫“¬§«“¡√ÈÕπ

ENGLISH

ELECTRICAL CONNECTIONS

To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all electrical connections before installing the unit.

•Be sure to ground this unit to the car’s chassis again after installation.

Notes:

•Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio dealer.

•It is recommended to connect to the speakers with maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 Ω to 8 Ω). If the maximum power is less than 50 W, change “AMP GAIN” setting to prevent the speakers from being damaged (see page 25 of the INSTRUCTIONS).

•To prevent short-circuit, cover the terminals of the UNUSED

leads with insulating tape.

• The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.

‰∑¬

°“√‡™◊ËÕ¡‚¥¬„™È‰øøÈ“

‡æ◊ËÕªÈÕß°π°“√‡°‘— ¥‰øøÈ“≈¥—«ß®√¢Õ·π–π”„ÀÈª≈¥¢«·∫µ‡µÕ√’Ë≈∫ÕÕ°È—·≈È«®÷ßµËÕ “¬‰ø°ËÕπµ‘¥µß‡§√◊ËÕßÈ—

•µ√«® Õ∫„ÀÈ·πË„®«Ë“‰¥È‡¥‘π “¬¥‘πµËÕ√–À«Ë“ß‡§√◊ËÕß°∫µ—«∂—ß— √∂¬πµÏ„À¡Ë·≈È«À≈ß®“°µ‘— ¥µßÈ—

À¡“¬‡Àµÿ:

•„™Èæ‘°¥—®”‡æ“–·∑πø‘« À“°ø‘« ¢Ï“¥∫ËÕ¬ „ÀÈª√÷°…“√È“ π¢“¬‡§√◊ËÕß‡ ¬ß√∂¬πµÏ’ JVC

•¢Õ·π–π”„ÀÈµËÕ≈”‚æß ∑’Ë¡’°”≈ß—¢∫— ßŸ ¥ÿ‡°‘π°«Ë“ 50 W

(∑ßÈ—¥È“πÀπÈ“·≈–¥È“πÀ≈ß— ¡’§Ë“§«“¡µÈ“π∑“π 4 Ω ∂÷ß 8 Ω) ∂È“°”≈ß—¢∫µË”°«Ë“— 50 W „ÀÈ‡ª≈’Ë¬π§Ë“ “AMP GAIN” ‡æ◊ËÕªÈÕß°— π‰¡Ë„ÀÈ≈”‚æß™”√ÿ¥ (¥ŸÀπÈ“ 25 §”·π–π”)

•°“√ªÈÕß°π°“√≈—¥—«ß®√ ®–µÈÕßæπ—¢«È— “¬µ–°«Ë— ∑’Ë‰¡Ë„™È·≈È«¥È«¬‡∑ ªæπ— “¬‰ø

•·ºËπ√–∫“¬§«“¡√ÈÕπ®–√ÈÕπ¡“°À≈ß®“°„™È—√–¡¥—√–«ßÕ¬Ë“‰ª— ¡º— —‡¡◊ËÕ∂Õ¥™ÿ¥ª√–°Õ∫π’È

A Typical Connections

Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this unit.

The leads of the power cord and those of the connector from the car body may be different in color.

1Connect the colored leads of the power cord in the order specified in the illustration below.

2Connect the antenna cord.

3Finally connect the wiring harness to the unit.

°“√‡™◊ËÕ¡µËÕ·∫∫ª°µ‘

°ËÕ•∑”°“•‡™•ËÕ¡µËÕ: µ•«®†Õ•°“•‡¥‘•†“¬‰ø„•••¬•µÏÕ¬Ë“ß•–¡—¥•–«Õ¬Ë“„ÀÈº‘— ¥æ•“¥„•°“•‡™•ËÕ¡µËÕ™ÿ¥ª•–°Õ•™ÿ¥•’ °“•‡™•ËÕ¡µËÕº‘¥æ•“¥Õ“®∑”„ÀÈ‡°‘¥§«“¡‡†’¬À“¬•È“¬·•ß°•™ÿ— ¥ª•– °Õ••’È‰¥È“•µ–°«—Ë¢Õß†“¬‰ø ·•–¢ÕßÕÿª°••ÏµËÕ‡™•ËÕ¡®“°µ«•— ß••Õ“®¡’†’∑’Ë‰¡Ë‡À¡•Õ•°•— 1 µËÕ “¬‰ø ’µ“¡≈”¥—∫∑’Ë√–∫ÿ„π√Ÿª¥È“π≈Ë“ß

2‡™◊ËÕ¡µËÕ°∫— “¬Õ“°“»

3¥ÿ∑È“¬ µËÕ «π§«∫§ÿ¡°“√‡Ë ¥‘π “¬‰ø‡¢È“°∫™ÿ— ¥ª√–°Õ∫™ÿ¥π’È

Rear ground terminal

®ÿ¥‡™◊ËÕ¡µËÕ “¬¥‘π¥È“πÀ≈ß—

		Line out
	Antenna terminal	(see diagram )
	Antenna terminal	“¬ÕÕ° (¥Ÿ·ºπ¿Ÿ¡ )
	¢—È« “¬Õ“°“»	“¬ÕÕ° (¥Ÿ·ºπ¿Ÿ¡ )

*2 Before checking the operation of this unit prior to installation, this lead must be connected, otherwise power cannot be turned on.

15 A fuse

ø‘« Ï¢π“¥ 15 A

Black

’¥”

Yellow*2

‡À≈◊Õß’ *2

Red

·’¥ß

Blue with white stripe

*1 Not included with this unit

*1 ‰¡Ë‰¥È„ÀÈ¡“°∫™ÿ— ¥ª√–°Õ∫π

To metallic body or chassis of the car

µËÕ°∫‚§√ß‚≈À—–À√◊Õ‡™ ´‘¢Õß√∂¬πµÏ

To a live terminal in the fuse block connecting to the car battery (bypassing the ignition switch) (constant 12 V)

µËÕ°∫—¢«∑’Ë¡’°√È— –· ‰øøÈ“„π·ºßø‘« Ï´÷ËßµËÕ°∫·∫µ‡µÕ√’Ë√∂¬πµ—

(‚¥¬‰¡ËµÈÕß„™È«‘∑™Ï®ÿ¥√–‡∫‘¥) (12 ‚«≈∑Ï§ß∑’Ë)

To an accessory terminal in the fuse block

µËÕ°∫—¢«È— «πª√Ë –°Õ∫„π·ºßø‘«

Ignition switch

«‘∑™Ï®ÿ¥√–‡∫‘¥

Fuse block

·ºßø‘«

*2 °ËÕπ°“√µ√«® Õ∫°“√∑”ß“π¢Õß™ÿ¥ª√–°Õ∫π’È°ËÕπ∑’Ë®–µ‘¥µßÈ—

µÈÕßµËÕ “¬µ–°«π’È°ËÕπË— ¡‘©–ππ®È—–‰¡Ë“¡“√∂‡ª‘¥‡§√◊ËÕß‰¥

πÈ”‡ß‘π≈“¬’ ¢“«

To the remote lead of other equipment or automatic antenna if any (200 mA max.)

µËÕ “¬°∫Õÿª°√≥ÏÕ◊ËπÀ√◊Õ‡— “Õ“°“»Õµ‚π¡—µ‘∂È“¡’—(¢π“¥ Ÿß ÿ¥ 200 mA)

	White with black stripe	White	Gray with black stripe		Gray	Green with black stripe	Green	Purple with black stripe		Purple
	¢’“«·∂∫¥”	’¢“«	‡∑“·∂∫’	¥”	’‡∑“	’‡¢’¬«·∂∫¥”	‡’¢’¬«	¡Ë«ß·∂∫’	¥”	¡Ë«ß’
		Left speaker (front)			Right speaker (front)		Left speaker (rear)			Right speaker (rear)
		≈”‚æß´È“¬ (ÀπÈ“)			≈”‚æß¢«“ (ÀπÈ“)		≈”‚æß´È“¬ (À≈ß)—			≈”‚æß¢«“ (À≈ß)—
B	Connections Adding Other Equipment /°“√µËÕ‡æ‘Ë¡‡µ‘¡‡¢È“°∫Õÿª°√≥ÏÕ◊Ëπ—

Amplifier / ‡§√◊ËÕß¢¬“¬

You can connect an amplifier and other equipment to upgrade your car stereo system.

•Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it can be controlled through this unit.

•Disconnect the speakers from this unit, connect them to the amplifier. Leave the speaker leads of this unit unused.

§ÿ≥ “¡“√∂µËÕ°∫·Õ¡æ≈‘ø“¬‡ÕÕ√Ï—·≈–Õÿª°√≥ÏÕ◊ËπÊ‰¥È‡æ◊ËÕ‡æ‘Ë¡§ÿ≥ ¿“æ‡ ’¬ß„ÀÈ°—∫√–∫∫ ‡µÕ√‘‚Õ¢Õß√∂¬πµÏ

•µËÕ “¬µ–°«√Ë—–¬–‰°≈ ( πÈ”‡ß‘π≈“¬’ ¢“«) ‡¢È“°∫— “¬µ–°«√Ë—–¬–‰°≈¢ÕßÕÿª°√≥ÏÕ◊Ëπ Ê ‡æ◊ËÕ®– “¡“√∂§«∫§ÿ¡‚¥¬™ÿ¥ª√–°Õ∫π’È‰¥È

•”À√∫‡§√◊ËÕß— ¢¬“¬‡∑Ë“ππ:È—

∂Õ¥≈”‚æßÕÕ°®“°™ÿ¥ª√–°Õ∫π’È·≈È«µËÕ‡¢È“°∫‡§√◊ËÕß— ¢¬“¬

∑‘Èß “¬µ–°«≈”‚æß—Ë ¢Õß™ÿ¥ª√–°Õ∫π’È‰«È

Rear speakers	Remote lead	Y-connector (not supplied for this unit)
≈”‚æßÀ≈ß—
	“¬µ–°«•Ë—–¬–‰°•	¢ÈÕµËÕ√Ÿªµ«— Y (‰¡Ë‰¥È„ÀÈ¡“°∫™ÿ— ¥ª√–°Õ∫π’È)

JVC Amplifier
‡§√◊ËÕß¢¬“¬‡ ’¬ß JVC	Remote lead (Blue with white stripe)

“¬µ–°«•Ë—–¬–‰°• ( πÈ”‡ß‘π≈“¬’ ¢“«)

*3 Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place not coated with paint (if coated with paint, remove the paint before attaching the wire).

KD-G498

To the remote lead of other equipment or automatic antenna if any

µËÕ “¬°∫Õÿª°√≥ÏÕ◊ËπÀ√◊Õ‡— “Õ“°“»Õµ‚π¡—µ‘∂È“¡’—

Failure to do so may cause damage to the unit.

*3—

Signal cord (not supplied for this unit)

“¬‡§‡∫‘≈ ≠≠“≥— (‰¡Ë‰¥È„ÀÈ¡“°∫™ÿ— ¥ª√–°Õ∫π’È)

Front speakers

≈”‚æßÀπÈ“

PRECAUTIONS on power supply and speaker connections:

•DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit will be seriously damaged.

•BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in your car.

¢ÈÕ§«√√–«ß— ”À√∫°“√µËÕ·À≈Ëß®Ë“¬°”≈—ß·≈—–≈”‚æß:

∫§«“¡‡ ¬À“¬¡“°’

•°ËÕπ∑’Ë®–µËÕ “¬µ–°«‡§‡∫‘≈°”≈Ë—ß—¢Õß≈”‚æß‡¢È“°∫≈”‚æß—

„ÀÈµ√«® Õ∫°“√‡¥‘π “¬‰ø≈”‚æß„π√∂¢Õß§ÿ≥„ÀÈ‡√’¬∫√ÈÕ¬‡ ¬°ËÕπ’

JVC KD-G498 manual

Models: KD-G498