Heat sink
iHš W×OH …—«d(«
•
•
•
•
• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio dealer.
• If noise is a problem...
This unit incorporates a noise filter in the power circuit. However, with some vehicles, clicking or other unwanted noise may occur. If this happens, connect the unit’s rear ground terminal (see connection diagram) to the car’s chassis using shorter and thicker cords, such as copper braiding or gauge wire. If noise still persists, consult your JVC car audio dealer.
• Maximum input of the speakers should be more than 45 watts at the rear and 45 watts at the front, with an impedance of 4 to 8 ohms.
• Be sure to ground this unit to the car’s chassis.
• The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.
•
ENGLISH
ELECTRICAL CONNECTIONS
To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all electrical connections before installing the unit. If you are not sure how to install this unit correctly, have it installed by a qualified technician.
Note:
This unit is designed to operate only on 12 volts DC, NEGATIVE ground electrical systems. If your vehicle does not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers.
U
WOzUÐdNJ
Handles
rJײ
Power cord
w
Hard case/Control panel
Sleeve
(Be sure to keep the handles after installing it.)
1
Parts list for installation and connection The following parts are provided with this unit.
After checking them, please set them correctly.
Insert the 2 handles into the slots, as shown.Then, while gently pulling the handles away from each other, slide out the unit.
1
2
3
1 Remove the control panel.
2 Remove the trim plate.
3
• Before removing the unit, release the rear section.
•
Removing the unit
Sleeve
w
…—UO
qO u² «
Dashboard
Mounting bolt
VO
Fire wall
s
Washer
ÂUJŠ«WIKŠ
• When using the optional stay
•
XO³¦²K
•When installing the unit without using the sleeve
In a Toyota for example, first remove the car radio and install the unit in its place.
TOYOTA
Æt½UJ w “UN'« VÒ— p – bFÐ ôË« …—UO « u¹œ«— Ÿe½« ¨Uðu¹uð Ÿu½ «—UOÝ w ¨‰U¦*« qO³Ý vKŽ
XO³¦ð bM
©w
Lock nut
XO³¦²
Screw (option)
©w
Flat type screws (M5 x 6 mm)*
(M5 x 6 mm)*
…bŽUI
*©rK M5®
Bracket*
*
*XO³¦²
Pocket
VOł
Bracket*
*
*XO³¦²
*Not included with this unit.
*
Flat type screws (M5 x 6 mm)*
(M5 x 6 mm)*
…bŽUI
*©rK M5®
Note: When installing the unit on the mounting bracket, make sure to use the 6 mm-long screws. If longer screws are used, they could damage the unit.
| 6mm™¯ | ∫WEŠö |
WwÆrK∂ ‰uÞ wž«dÐ Âbsb¨XO³¦²WOH²vKŽ “UN'« VObMŽ |
| Æ“UN'« —d{ Ë« nKð V³ | |
…—UO
ÆwHK)« ¡e'« —dŠ ¨“UN'« Ÿe½ q³ | • |
ÆrJײ | ± |
ÆWM¹e | ≤ |
Æq?J?A? | ≥ |
sŽ …bŠ«u«bOFÐ W5²V×Ý ¡UMŁ« ¨pbFÐ | |
Æ×U)« v | |
©“UN'« VO | |
Handle
W
Trim plate
WM¹e
Washer (ø5) | Lock nut (M5) |
(ø5) | (M5) |
ÂUJŠ« WIKŠ | ©M5® XO³¦² |
©µ dD | |
qO
Æ“UN'« l
Æ`O×
Remote controller
bFÐ sŽ rJײ
Mounting bolt (M5 x 20 mm) (M5 x 20 mm)
©rK≤∞ ™ M5® VO—UL
Battery
U¹—UD³
CR2025
Rubber cushion
WOÞUD*« …uA(«
WOzUÐdNJ
| ·d??Þ q??B??H??Ð w?? | öOqLŽ rŁ VW¹—UD³ |
| Æ“UN'« VOq³WOzUÐdNJ |
| v?łd?¹ ¨`?O?×? | |
| Ác¼ q¦VOq¼Rh²h“UN'« VOWOKLŽ „dð |
| | Æ…eNłô« |
12V | | ∫WEŠö |
JVC | ±≤ ¨DC d?ýU?³? | —U?O?ð W?D?Ý«u?Ð q?L?FO |
| «c¼ q¦œułË ÂbŽ WwÆ | V i¹—Qð WOzUÐdNWLE½« ¨X |
| «c¼ ¡«dý sJ1Ë ¨ÃU²‰u׫bV−¹ ¨pð—UOÝ wÂUEM | |
| ÆJVC W | | |
| —d?J?ð «–« ÆW? | | • |
| «—UOWOðuB…eNłô« ¡ö…—UA²Ý« vłd¹ ¨“uOH‚«d²Š« | |
| | ÆJVC W |
| | ÆÆÆWKJA*« u¼ ZO−C | • |
| lÆWOzUÐdNJW…dz«œ qš«œ ZO−{ d²K“UN'« «c¼ Âb | |
| Ë« W??I??D??I??D? | | |
| JVC ·d??Þ q?? | “UN'« WOHKš wœułu*« | i¹—Q² |
| ©qHÝô« wqOrÝ— dE½«® |
| q?¦? | | |
| WIDIDnÂbŽ WwÆwÝUOIpKÝ Ë« ‰Ëb:« ”U×MpKÝ | |
| «—U?O? | ÆJVC W |
| ◊«Ë ¥∞ s?? |
| | • |
| ¥ 5?Ð WF½U2 l | ÆÂË« ∏ v |
| |
Æ…—UO | • |
s? | • |
| Æ“UN'« Ÿe½ bMŽ UN² |
