Network Basic Page

This page is for performing basic setting related to the network.

This page can be used during access using AadminB.

●Click [Advanced Settings] to display setting menu.

●Click [Network Basic].

●Press the [OK] button to enable the new settings.

●If the [OK] button is pressed upon entering an invalid value, a warning message will appear and the entry will be denied. Press the [Cancel] button to restore the invalid entry to the current value.

●When settings of the [Network Basic] page is changed, all services that are currently running will end immediately. For example, when changes are made to the [Network Basic] page during JPEG/ MPEG4 distribution, distribution will be discontinued and TCP will be disconnected.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

B

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

E

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

G

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

H

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

I

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Click

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A IP Setting

For setting the DHCP client function.

 

 

 

 

 

Connect the camera to a network environment with a DHCP server when

 

 

 

 

 

DHCP is to be enabled.

 

 

 

 

 

If the DHCP server does not exist when DHCP is set to AEnableB, Camera

 

 

 

 

 

will start running with the 192.168.0.2 IP address and 255.255.255.0 subnet

 

 

 

 

 

mask in about 2 minutes after startup.

 

 

 

 

 

Refer to AIP Address SettingsB (A Page 6) for the IP address.

 

 

B IP Address

For setting the IP address of the camera.

 

 

C Subnet Mask

For setting the subnet mask of the camera.

 

 

D Default Gateway

For setting the default gateway of the camera.

 

 

 

 

 

Set as 0.0.0.0 when a default gateway is not set.

 

 

E Host Name

For setting the host name of the camera.

 

 

 

 

 

Specify a name using alphanumeric characters, hyphen (-) or period (.).

 

 

 

 

 

Underscores (_) cannot be used.

 

 

F DNS Server

For setting the address of the DNS server.

 

 

G MAC Address

The MAC address of the camera is displayed in a hexadecimal number.

 

 

H IP Protocol

For setting IPv6 to On or Off. (IPv4 is set to On at all times.)

 

 

I IPv6 Address

Two types of addresses, “link local” and “global”, are displayed when IPv6

 

 

 

 

 

settings are enabled. However, if the connected network does not support

 

 

 

 

 

IPv6, “Disabled” appears in the “global” address field.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

45