EN23
Menu Screen Explanations
CAMERA MENU
| FADER/WIPE | Refer to “Fade/Wipe Effects” ( pg. 28, 29). | ||
| ||||
| ||||
| P.AE/EFFECT | Refer to “Programme AE With Special Effects” ( pg. 30, 31). | ||
| W.BALANCE | Refer to “White Balance Adjustment” and “Manual White Balance Operation” | ||
|
|
| ( pg. 33). |
|
| REC MODE | Allows you to set the recording mode (SP or LP) depending on your | ||
| ||||
|
|
| preference ( pg. 11). |
|
|
|
|
| |
| SOUND | 12 BIT | Enables recording of stereo sound on four separate channels, and is | |
| MODE |
| recommended for use when performing audio dubbing. (Equivalent to the | |
|
|
| 32 kHz mode of previous models) | |
|
| 16 BIT | Enables recording of stereo sound on two separate channels. (Equivalent to the | |
|
|
| 48 kHz mode of previous models) | |
|
|
|
| |
| ZOOM | 10X | When set to “10X” while using digital zoom, the zoom magnification will | |
|
|
| reset to 10X since digital zoom will be disengaged. | |
|
|
|
| |
|
| 40X | Allows you to use the Digital Zoom. By digitally processing and magnifying | |
|
|
| images, zooming is possible from 10X (the optical zoom limit), to a maximum | |
|
|
| of 40X digital magnification. |
|
|
| 200X | Allows you to use the Digital Zoom. By digitally processing and magnifying | |
|
|
| images, zooming is possible from 10X (the optical zoom limit), to a maximum | |
|
|
| of 200X digital magnification. |
|
|
|
|
|
|
| SNAP | FULL | Refer to “Snapshot” ( pg. 16). |
|
| MODE |
|
| |
|
|
|
| |
| GAIN UP | OFF | Allows you to shoot dark scenes with no picture brightness adjustment. | |
|
|
|
| |
|
| AGC | The overall appearance may be grainy, but the image is bright. | |
|
|
|
| |
|
| AUTO | The shutter speed is automatically adjusted (1/25 — 1/200 sec.). Shooting a | |
|
|
| subject in low or poor lighting at 1/25 sec. shutter speed provides a brighter | |
|
|
| image than in the AGC mode, but the subject’s movements are not smooth or | |
|
|
| natural. The overall appearance may be grainy. When shooting a subject in | |
|
|
| low lighting in this mode, “ | ” is displayed. |
| BEEP/ | ON: MEL. | The tally lamp comes on to signal the start of recording. Instead of a beep, a | |
| TALLY |
| melody sounds when any operation is performed. It also activates the shutter | |
|
|
| sound effect ( pg. 16). |
|
|
| ON: BEEP | The tally lamp comes on to signal the start of recording. | |
|
|
| The beep sounds when the power is turned on or off, and at the beginning and end | |
|
|
| of recording. Also to activate the shutter sound effect ( pg. 16). | |
|
|
|
| |
|
| OFF | The tally lamp remains off at all times. | |
|
|
| Even though not heard while shooting, shutter sound is recorded on the tape. | |
|
|
|
| |
| ID NUMBER | This number is necessary when connecting the camcorder to a device such as | ||
|
|
| a computer using the J terminal (JLIP). The numbers range from 01 to 99. | |
|
|
| Factory setting is 06. |
|
|
|
|
|
|
:
NOTE:
The “ CAMERA MENU” settings are effective when the Operation Switch is set to both “ ” and “ ”.
CONTINUED ON NEXT PAGE