TV
CATV/
DBS

Operating Other Manufacturers’ Equipment

You can use this remote control supplied for operating other manufacturers’ components, either by changing the preset signal codes or by using the learning function (see page 78).

English

IMPORTANT:

•To operate the other component(s) using the RF signals emitted from this remote control, the IR signal transmitter and the RF rod antenna must be connected to this receiver.

–Place the IR signal transmitter so that it is aimed at the remote sensor(s) on the target component(s).

–The RF signal-reachable distance may differ depending on the operating conditions and circumstances.

–The IR signal transmitter can send signals at a distance of 3 m (10 feet).

When using the remote control:

–Set the ZONE 1/ZONE 2 (LEARN/TRANSMIT) selector to “ZONE 1” or “ZONE 2” correctly.

LEARN TRANSMIT

LEARN TRANSMIT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ZONE 1

 

ZONE 2

ZONE 1

 

ZONE 2

–Set the TV operation mode selector to “TV” or

“CATV/DBS” correctly.

To operate TV, set it to “TV.”

Changing the Preset Signal Codes

By changing the transmittable signals from preset ones to the other manufacturers’, you can operate the other manufacturer’s components using this remote control.

•When operating the other manufacturers’ components, refer also to the manuals supplied with them.

To change the transmittable signals for operating another manufacturer’s TV

1. Set the TV operation mode selector to

“TV.”TV

CATV/

DBS

2.

Press and hold TV/CATV/DBS

TV/CATV/DBS

 

(STANDBY/ON).

STANDBY/ON

 

 

3.

Press TV/DBS.

 

To operate the CATV converter or the DBS tuner, set it to “CATV/DBS.”

–Check the indication shown on the remote’s display

when you press a button—this indicates the remote control operation mode together with multi-room operation mode (either ZONE 1 or ZONE 2) for a while.

LEARN

TRANSMIT

 

LEARN

TRANSMIT

 

 

STANDBY

ON

 

STANDBY

ON

ZONE 1

ZONE 2

 

ZONE 1

ZONE 2

 

 

ZONE 1

ZONE 2 TV/CATV/DBS

 

ZONE 1

ZONE 2 TV/CATV/DBS

VCR 1

VCR 1

 

 

 

ON/OFF

ON/OFF

 

ON/OFF

ON/OFF

 

 

STANDBY/ON

STANDBY/ON

 

STANDBY/ON

STANDBY/ON

 

 

 

 

Remote’s display

4. Enter a manufacturer’s code using buttons 1–9, and 0.

See page 76 to find the code.

TV/DBS

 

 

EFFECT

1

2

3

 

 

LIVENESS

4

5

6

7/P

8

9

10

0

+10

RETURN

FM MODE

100+

ZONE 1

ZONE 2

Ex. When you press VCR1

Ex. When you press VCR1

with ZONE 1/ZONE 2

with ZONE 1/ZONE 2

(LEARN/TRANSMIT)

(LEARN/TRANSMIT)

selector set to “ZONE 1.”

selector set to “ZONE 2.”

 

 

CAUTION:

When replacing the batteries, finish changing them without delay;

otherwise, preset manufacturers’ codes will be reset.

5. Release TV/CATV/DBS (STANDBY/ON).

After setting the TV operation mode selector to “TV,” you can perform the following operations on the TV:

TV/CATV/DBS

(STANDBY/ON)

: Turns on or off the TV. TV VOL +/– :Adjusts the volume.

TV/VIDEO : Sets the input mode (either TV or VIDEO).

After pressing TV/DBS (with the TV operation mode selector set to “TV”), you can perform the following operations on a TV:

CHANNEL +/–

: Changes the channels.

1–10, 0, 100+ (+10)

: Selects the channels.

 

 

Number button 10 will function as

 

 

the ENTER button if your TV

 

 

requires pressing ENTER after

 

 

selecting a channel number.

Notes:

 

 

•Refer to the manual supplied for your TV.

•All the buttons listed above may not be used for some TVs.

•If you cannot change the channels of some TVs by pressing number buttons, press CHANNEL +/– .

6. Try to operate your TV by pressing TV/CATV/DBS

TV/CATV/DBS (STANDBY/ON).

STANDBY/ON

When your TV turns on or off, you have entered the correct code.

If more than one code is listed for your brand of TV, try each

one until the correct one is entered.

74