Ken-A-Vision X1000 Vertical Projection, Microprojector Operating Instructions

USE AS A MICROSCOPE

(Requires optional 10x eyepiece tube)

1.Rotate the light diffusing lens (item #6) until it is under the light beam.

2.Place the unit in the horizontal position.

3.View the specimen through the 10x eyepiece tube. (optional accessory for this model)

4.Bring into focus using the focusing knob (item #9)

MICROPROJECTOR OPERATING INSTRUCTIONS

The microprojector will project either horizontally or vertically. When used with a large group or entire class, project from the horizontal position. For small groups or an individual, projectect vertically. Use whenever possible, as everyone sees the same image, making it ideal for study, discussions, and lectures.

MODEL TYRO

OPERATING INSTRUCTIONS

Instructions covering the use of the Ken-A-Vision Microprojector Model Tech A-11 apply except for the following:

1.Under”Vertical Projection” discard #4.

2.Under”Vertical Projection” discard #8.

LIGHT POLARIZATION

1.Rotate the polarizing lens/analyzer (item #5-darker lens and #14) until the lens es are beneath the light beam.

2.Place a slide containing polarizing material on the stage item (item#8).(Option to prepare a slide, crumple a small amount of cellophane from a cigarette wrapper, stick it to a strip of scotch tape approximately 2 inches long; then place it on a slide).

3.Bring into focus and change colors by turning the polarizing lens/analyzer.

1.Lamp Housing Cap

2.Lamp Housing Cap

Screw

3.Horizontal Positioning Tension Bolt

5.Light Diffusing Lens

7.Stage Clip or Optional Mechanical Stage

9.Focusing Knob

16.10x Eyepiece Tube

Model X1000-1

4. Lamp Housing

6.Polarizing Lens Analyzer

8. Stage

11.16mm Lens

12.10mm Lens

136.5 mm Lens

10.Revolving Lens Turret

14.Dust Proof Revolving Disk

15.Mirror

USE AS A MICROSCOPE

(requires optional 10x eyepiece tube)

1.Rotate the light diffusing lens (item#6-white) until it is under the light beam.

2.Place the unit in the horizontal position.

3.View the specimen through the 10X eyepiece tube. (Purchase as an accessory.)

4.Bring into focus using the focusing knob (item#9).

LAMP REPLACEMENT- ALL MICROPROJECTORS

1.When a lamp burns out, the switch MUST be placed in the “off” position and the unit UNPLUGGED.

2.DO NOT replace until lamp has cooled.

3.Remove the lamp housing cap screws (item#2), lift off the lamp housing cap (item #1), and replace the defective lamp. Use KAVGE EKL 150W lamp.Use as soft cloth when replacing the lamp - Do Not touch with your bare hands

KEEP COVERED WHEN NOT IN USE -DUST IS ITS ENEMY

ACCESSORIES

(available from the factory)

KAVOL065 6.5mm Lens (43x)	KAVOL010	10mm Lens (20x)
KAVOL016 16mm Lens (10x)	KAVOL030	30mm Lens (4x)
KAVEP001 10x Eyepiece Tube	T5045 Mechanical Stage
KAVGEEKL Lamp (Quartz Iodine 150 watt	KAVEXPM Classroom Experimental Manual
KAVSCOACT - Laboratory Activity Book	T5090 - Vinyl Dust Cover (large)

VERTICAL PROJECTION

1.Turn the switch to the “ON” position.

2.Place a white sheet of paper between the legs of the base.

3.Rotate lenses (item #5 and #6) and mirror (item #15), so the light beam will not be obstructed.

4.Rotate revolving lens turrent (item #10) containing the three lenses, (item #11) is positioned over until the 16mm lens so the light beam penetrates it.

5.Rotate the Dust Proof Revolving disk (item #14) until the RED “C” on the side of the disk is directly under the RED line on your upper disk.

6.Place a specimen slide between the prongs of the mechanical stage (item #7) or under the stage clips, and center it under the light.

7.Using the focusing knob (item #9), at either side, lower the stage (item #8) to the lowest position and then reverse the direction until the specimen is brought into focus.

8.To use the 5x Wide Field auxiliary lens, rotate the revolving dust proof revolving disk (item #14) until the RED “A” is under the RED line on the upper disk.