Kenmore 110.24975 manual Installation Requirements

INSTALLATION

REQUIREMENTS

Assemble the necessary tools and supplies before beginning the washer installation. The parts supplied are in the washer basket.

Tools needed for connecting the drain hose and water inlet hoses:

•Pliers that open to 19/16in. (3.95 cm)

•Flashlight (optional)

Parts supplied:

3 4 5

1.Drain hose

2.Silver, double-wire hose clamp (for the bottom of the drain hose)

3.Yellow, single-wire hose clamp (for the top of the drain hose)

4.Water inlet hoses (2)

5.Flat water inlet hose washers (4)

Tools needed for securing the drain hose and leveling the washer.

•Adjustable or open end wrench %6in. (14 mm)

•Level

•Wood block

•Ruler or measuring tape

Parts supplied:

12

1.Shipping strap with fastener

2.Front leveling feet with nuts (2)

Alternate Parts

Parts listed are available from your local Sears store or Sears Service Center. For further information, please call 1-800-4-MY- HOME ® (1-800-469-4663}.

If You Have:		You Will Need to Buy:
Laundry tub or		Sump	pump			system	(if not already
standpipe	taller	available)
than 96 in. (2.4 m)
1 in. (2.5 cm)		2 in. (5 cm) diameter					to	1 in. (2.5 cm)
diameter		diameter		standpipe adapter, Part No.
standpipe		3363920
Overhead	sewer	Standard		20 gaL (76 L) 39 in. (99 cm) tall
		drain tub or utility sink, sump pump and
		connectors			(available		from		local
		plumbing		suppliers)
Floor drain		Siphon	break, Part Number						285320;
		additional drain hose, Part Number
		3357090		and		connector		kit,
		Part Number				285442
Water faucets		2 longer		water fill hoses:
beyond reach of		6 ft (1.8 m) Part Number						76314,
fill hoses		10 ft (3.0 m) Part Number 350008
Drain hose	too	Drain hose,			Part No. 388423 and hose
short		kit, Part		No.	285442

Drain hose that is Hose kit, Part No. 285442 too long

Lint clogged drain Drain protector, Part No. 367031

Selecting the proper location for your washer improves performance and minimizes noise and possible washer "walk."

Your washer can be installed in a basement, laundry room, closet, or recessed area. (See "Drain System.")

IMPORTANT: Do not install or store the washer where it will be exposed to the weather.

Proper installation is your responsibility.

You will need:

•A water heater set to deliver 120°F (49°C) water to the washer.

A grounded electrical outlet located within 4 ft (1.2 m) of where the power cord is attached to the back of the washer. (See "Electrical Requirements.")

Hot and cold water faucets located within 4 ft (1.2 m) of the hot and cold water fill valves, and water pressure of 5-100 psi (34.5-690 kPa). Washers with triple dispensers require 26-100 psi (138-690 kPa) for best performance.

A level floor with a maximum slope of 1 in. (2.5 cm) under

entire washer. Installing the washer on carpeting is not recommended.

•A sturdy floor to support the washer weight (washer, water and load) of 315 Ibs (143 kgs).

Do not store or operate your washer in temperatures at or below 32°F (0°C). Some water can remain in the washer and can cause damage in low temperatures. See "Washer Care" for winterizing information.