WATER SYSTEM PIPING

Piping Installation

Piping, fittings, and valves should be installed according to the installation drawing (Figure 22). If the indoor installation area is subject to freezing temperatures, the water piping must be protected by insulation.

The water supply pressure should not exceed 80 psi. If this occurs, a pressure reducing valve with a bypass may need to be installed in the cold water inlet line. This should be placed on the supply to the entire house in order to maintain equal hot and cold water pressures.

IMPORTANT: Heat cannot be applied to the water fittings on the heater as they may contain nonmetallic parts. If solder connections are used, solder the pipe to the adapter before attaching the adapter to the hot and cold water fittings.

IMPORTANT: Always use a good grade of joint compound and be certain that all fittings are drawn up tight.

1.Install the water piping and fittings as shown in Figure 22. Connect the cold water supply (3/4” NPT) to the cold water inlet fitting. Connect the hot water supply (3/4” NPT) to the hot water outlet fitting.

IMPORTANT: Some models may contain energy saving heat traps to prevent the circulation of hot water within the pipes. Do not remove the inserts within the heat traps.

2.The installation of unions in both the hot and cold water supply lines is recommended for ease of removing the water heater for service or replacement.

3.The manufacturer of this water heater recommends installing a mixing valve or an anti-scald device in the domestic hot water line as shown in Figure 23. These valves reduce the point-of-use temperature of the water by mixing cold and hot water and are readily available for use.

4.If installing the water heater in a closed water system, install an expansion tank in the cold water line as specified under “Closed System/Thermal Expansion.”

5.Install a shut-off valve in the cold water inlet line. It should be located close to the water heater and be easily accessible. Know the location of this valve and how to shut off the water to the heater.

6.A temperature and pressure relief valve must be installed

in the opening marked “Temperature and Pressure (T & P) Relief Valve” on the water heater. A discharge line must be added to the opening of the T&P Relief Valve. Follow the instructions under “Temperature and Pressure Relief Valve.”

7.After piping has been properly connected to the water heater, remove the aerator at the nearest hot water faucet. Open the hot water faucet and allow the tank to completely fill with water. To purge the lines of any excess air, keep the hot water faucet open for 3 minutes after a constant flow of water is obtained. Close the faucet and check all connections for leaks.

IN A CLOSED SYSTEM USE A

THERMAL EXPANSION TANK

COLD WATER SUPPLY TO FIXTURES

PRESSURE REDUCING VALVE

WITH BYPASS

HOT WATER

COLD WATER

OUTLET

INLET

COLD WATER INLET VALVE (SHUT-OFF VALVE)

 

TEMPERATURE AND PRESSURE (T&P)

 

RELIEF VALVE (OPTIONAL TOP T&P

 

RELIEF VALVE NOT SHOWN)

 

DISCHARGE PIPE

 

(DO NOT CAP OR PLUG)

 

 

 

MASSACHUSETTS: INSTALL

 

DRAIN LINE

A VACUUM RELIEF IN COLD

 

3/4” ID

 

WATER LINE PER SECTION

1” MINIMUM

MINIMUM

19 MGL 142.

 

 

 

METAL

 

6” MAXIMUM

DRAIN PAN

 

AIR GAP

DRAIN

 

 

 

FIGURE 22.

 

 

 

TEMPERED WATER

UNTEMPERED

TO FIXTURES

 

 

 

HOT WATER

 

 

COLD

 

 

 

 

 

 

WATER

 

 

 

INLET

HOT

WATER

OUTLET

MIXING VALVE (SET TO 120°F)

FOLLOW THE MIXING

VALVE MANUFACTURER’S

INSTRUCTIONS

FIGURE 23.

Please note the following:

The system should be installed only with piping that is suitable for potable (drinkable) water such as copper, CPVC, or polybutylene. This water heater must not be installed using iron piping or PVC water piping.

Use only pumps, valves, or fittings that are compatible with potable water.

It is recommend that only full flow ball or gate valves are used in water piping installations. The use of valves that may cause excessive restriction to water flow is not recommended.

Use only 95/5 tin-antimony or other equivalent solder. Any lead based solder must not be used.

Piping that has been treated with chromates, boiler seal, or other chemicals must not be used.

Chemicals that may contaminate the potable water supply must not be added to the piping system.

21

Page 21
Image 21
Kenmore 153.332.410 manual Water System Piping, Piping Installation

153.332.410 specifications

The Kenmore 153.332.410 is a versatile and efficient appliance that has gained popularity among homeowners looking for both functionality and reliability. This model exemplifies the high standards that Kenmore is known for, contributing to a seamless laundry experience.

One of the standout features of the Kenmore 153.332.410 is its user-friendly design. The intuitive control panel makes it easy for users to select appropriate settings for a variety of fabrics and loads. With multiple wash cycles available, including delicate, normal, and heavy-duty, the appliance caters to a range of laundry needs, ensuring your clothes are treated with care.

Another key characteristic is the capacity of the drum. The generous space allows users to wash larger loads in one go, saving time and energy. This is particularly beneficial for families or individuals with substantial laundry needs, as it minimizes the number of cycles needed, making laundry days far more efficient.

In terms of technology, the Kenmore 153.332.410 incorporates advanced washing capabilities, including a powerful agitation system that ensures thorough cleaning. The appliance effectively removes tough stains while being gentle enough for delicate items. Additionally, it features a high-efficiency design that reduces water and energy consumption without compromising performance.

The steam cleaning feature is noteworthy, as it not only helps in removing stubborn stains but also reduces wrinkles in garments, making ironing less of a chore. This technology is favored by many users, as it simplifies post-laundry tasks. Noise reduction technology also adds to the appliance's appeal, allowing it to operate quietly in the background, which is particularly valuable for apartments or homes where laundry is done overnight.

Durability is another aspect where the Kenmore 153.332.410 excels. Built with high-quality materials, this model is designed to withstand the rigors of frequent use. Its robust construction provides peace of mind that the appliance will deliver performance for years to come.

In conclusion, the Kenmore 153.332.410 stands out in the competitive landscape of laundry appliances. With its user-friendly features, advanced technology, generous capacity, and durability, it offers a comprehensive solution for all laundry needs, making it a worthy investment for any household.