17
■Turn the TURBOZONE™ wash option off if not loading items
for this option. Always use heavy soil detergent fill
recommendation with TURBOZONE™ wash option. (See
“How much detergent to use” in “Detergent Dispenser”
section.)

Hi Temp

Select this option to increase the water temperature during the
wash portions of the cycle. Hi Temp wash raises the water
temperature to 145ºF (63ºC), in the main wash. Heating the water
helps improve washing results. Hi Temp wash is useful when
loads contain tough food soil.
This option may add heat and wash time to the cycle.
NOTE: Hi Temp wash is an option with the SMART WASH™,
Pots Pans, and Normal Wash cycles.

Sani Rinse

Select this option to raise the water temperature in the final rinse
to approximately 155°F (68°C). Sani Rinse adds heat and time to
the cycle. This high temperature rinse sanitizes your dishes and
glassware in accordance with NSF/ANSI Standard 184 for
Residential Dishwashers. Certified residential dishwashers are
not intended for licensed food establishments.
NOTE: Sani Rinse is an option with SMART WASH™, Pots Pans,
and Normal Wash cycles. Only these sanitization cycles have
been designed to meet the NSF/ANSI requirements.

Heated Dry

The Heated Dry option in combination with rinse aid will give you
excellent drying results. The energy to use Heated Dry costs
pennies per cycle. Heated Dry is on when the light is lit on the
Heated Dry button. Be sure to load plastic items in the upper rack
to avoid damage.
You may turn off the Heated Dry option by pressing HEATED DRY
so that the light goes off. However, you will have items in your
dish load that will not be dry at the end of the cycle.
NOTE: The Heated Dry option is used in all cycles except Fast
Wash an d Quick R inse.

Lock On

Use the Lock On to prevent unintended use of the dishwasher
between cycles. You can also use the lock feature to prevent
unintended cycle or option changes during a cycle.
When Lock On is lit, all buttons are disabled.
NOTE: The dishwasher door can be opened while the controls
are locked. However, the lock must be turned off and the Start/
Resume button pressed to resume the cycle.

To turn on the Lock

Press and hold HEATED DRY for 4seconds. Lock On glows.
If you press any pad while your dishwasher is locked, the l ight
flashes 3 times.
NOTE: If the Heated Dry option is selected, the light will
temporarily turn off until Lock On glows.

To turn off the Lock

Press and hold HEATED DRY for 4seconds. The light turns off.

Delay Hours

Select this option to run your dishwasher at a later time or during
off-peak hours. You can add items to the load anytime during the
delay. After adding items, firmly close the door until it latches and
press START/RESUME, or the delay will not continue.

To delay the start

1. Press the delay button to choose the number of hours
delayed.
2. Select a wash cycle and options.
3. Press START/RESUME.
The dishwasher starts the cycle in the selected number of hours.
NOTES:
■To cancel the delay and cycle, press CANCEL/DRAIN.
■To cancel the delay and start the cycle, press START/
RESUME.
Cycle Status Indicators
Follow the progress of your dishwasher with the Cycle Status
indicators.
NOTE: The features on your dishwasher may vary from those
shown here.

Clean

Clean glows when a cycle is finished. The light turns off when you
press any button or close the door.

Sanitized

If you select the Sani Rinse option, Sanitized glows when the
Sani Rinse cycle is finished. If your dishwasher did not properly
sanitize your dishes, the light flashes at the end of the cycle. This
can happen if the cycle is interrupted or the incoming water
temperature is too low. The light turns off when you press any
button or close the door.
Side view of TURBOZONE™ wash area