Introduction

 

 

2

Before applying power

CD-206/204/203/DPF-R6010/R4010/R3010 (En)

Caution : Read this section carefully to ensure safe operation.

 

 

 

 

 

 

Units are designed for operation as follows.

U.S.A. and Canada .........................................................

AC 120 V only

Australia ..........................................................................

AC 240 V only

U.K. and Europe

............................................................. AC 230 V only

China ...............................................................................

AC 220 V only

*Other countries

......................... AC 110-120 / 220-240 V switchable

*AC voltage selection

The AC voltage selector switch on the rear panel is set to the voltage that prevails in the area to which the unit is shipped. Before connecting the power cord to your AC outlet, make sure that the setting position of this switch matches your line voltage. If not, it must be set to your voltage in accordance with the following direction.

Note:

Our warranty does not cover damage caused by excessive line voltage due to improper setting of the AC voltage selector switch.

AC voltage selector switch

 

 

 

The illustration shows

AC110-220V

AC220-240V

the CD-206/DPF-R6010.

LINE OUTPUT

SYSTEM CONTROL

DIGITAL OUTPUT

 

VARIABLE

ƒ

COAXIAL OPTICAL

 

L

 

 

 

 

SL16 XS 8

 

 

R

 

 

 

AC110-220V AC220-240V

 

TEXT

 

 

 

 

Move switch lever to match your line voltage with a small screwdriver or other pointed tool.

For the United Kingdom
Factory fitted moulded mains plug

1.The mains plug contains a fuse. For replacement, use only a 13-Amp ASTA-approved (BS1362) fuse.

2.The fuse cover must be refitted when replacing the fuse in the moulded plug.

3.Do not cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or adapter, or consult your dealer.

If nonetheless the mains plug is cut off, remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply.

IMPORTANT

The wires in the mains lead are coloured in accordance with the following code:

Blue

: Neutral

 

Brown

: Live

 

Do not connect those leads to the earth terminal of a three-pin plug.

 

 

 

Safety precautions

Caution : Read this section carefully to ensure safe operation.

 

 

 

WARNING : TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAINOR MOISTURE.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED “DANGEROUS VOLTAGE” WITHIN THE PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.

THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.

REQUIREMENT BY NEDERLAND GAZETTE

Batteries are supplied with this product. When they empty, you should not throw away. Instead, hand them in as small chemical waste.

The marking of products using lasers (Except for some areas)

CLASS 1

LASER PRODUCT

The marking is located on the rear panel and says that the component uses laser beams that have been classified as Class 1. It means that the unit is utilizing laser beams that are of a weaker class. There is no danger of hazardous radiation outside the unit.