In case of difficulty
| |
What appears to be a malfunction may not always be serious. If your unit should not perform as expected, consult the |
|
table below to see if the problem can be corrected before seeking help from your dealer or service representative. | 23 |
|
The microcomputer may fall into malfunction (impossibil- ity to operate, erroneous display, etc.) when the connection cords are unplugged while the unit is ON or due to an external factor. In this case, execute the following method to reset the microcomputer and return it to normal condi- tion.
Set the unit to STANDBY mode by pressing ON/ STANDBY (
) switch, and after a few seconds, turn the unit ON by pressing the ON/STANDBY (
) switch again.
ÖPlease be aware that resetting the CD player will erase all stored information and return it to the factory settings.
| Symptom | Cause | Remedy |
| |
|
|
|
|
| |
| The unit is not turned ON with the ON/ | ÖPower plug is loosely connected. | ÖInsert the power plug firmly to the AC outlet. | |||
| STANDBY ( |
| ) switch ON. | ÖWith the power plug connected to the switched | ÖTurn the amplifier’s power ON. |
|
|
| ||||
|
|
| AC outlet of an amplifier, the power of the |
|
|
|
|
| amplifier is turned off. |
|
|
|
|
|
|
| |
| Disc is loaded, player does not play. | ÖDisc is loaded upside down. | ÖLoad the disc again with its label side up. | |||
|
|
| ÖDisc is loose. | ÖInsert the disc properly. |
|
|
|
| ÖDisc is dirty. | ÖWipe off the dust on the surface of the disc | |
|
|
| ÖDisc is cracked. | referring to “Disc handling precautions”. ª | |
|
|
| ÖReplace the disc with a new one. |
| |
|
|
| ÖCondensation has occurred on the optical lens | ÖLeave the player for about 1 hour so that the | |
|
|
| unit. | condensation is removed. | ª |
|
|
|
|
|
|
| No sound. |
|
| ÖPlay mode is not entered. | ÖPress the 6key. |
|
|
|
| ÖDisc is too dirty. | ÖWipe off the dust on the disc surface referring | |
|
|
| ÖDisc is cracked. | to “Disc handling precautions”. | ª |
|
|
| ÖReplace the disc with a new one. |
| |
|
|
| ÖThe connection cords are inserted loosely. | ÖConnect all connection cords firmly. |
|
|
|
| ÖOutput level is attenuated too low. | ÖAdjust the output level with OUTPUT key on | |
|
|
|
| the remote control unit. | 5 |
|
|
| |||
| Music is interrupted. (Sound is skipped.) | ÖDisc is too dirty. | ÖWipe off the dust on the disc surface referring | |||
|
|
| ÖDisc is cracked. | to “Disc handling precautions”. | ª |
|
|
| ÖReplace the disc with a new one. |
| |
|
|
| ÖOscillation is applied to this unit. | ÖTry selecting a place where no strong vibra- | |
|
|
|
| tions occur by changing the installation place, | |
|
|
|
| etc. |
|
|
|
| |||
| Play begins as soon as the unit is turned | ÖThis unit is designed so that play begins auto- | ÖIf automatic play is not required, remove the | |||
| ON. |
|
| matically when the unit is turned ON if a disc | disc from the player before setting the unit to | |
|
|
| is already loaded. | STANDBY mode. |
|
|
|
|
|
|
|
Symptom | Cause | Remedy |
|
|
|
|
|
| Remote control operation is not possi- | ÖBatteries are exhausted. | ÖReplace with new batteries. | 8 |
| ble. | ÖThe remote control unit is too far away from | ÖOperate the remote control unit within the con- | |
| the main system, controlling angle is too large, | trollable range. | 8 |
| or there is an obstacle in between. |
|
|
|
|
|
|