In case of difficulty
What seems to be a malfunction is not always so. Before calling for service, check the following table ac- cording to the symptom of your trouble.
|
| Symptom | Remedy |
|
|
| Sound is not produced. | ÷ Connect properly referring to "Connections". | 67 |
|
|
| ÷ Adjust to a required volume. | 9 |
ENGLISH |
|
| ÷ Select the desired input source with the INPUT SELECTOR | |
|
| knob. | 9 | |
|
|
| ||
|
|
|
| |
|
| No sound is output or noise interferes. | ÷ The speaker protection circuit may be activated. Read “Speaker | |
|
|
| protection circuit” below and remove | |
|
|
| speaker cords. | 0 |
|
|
| ||
|
|
|
|
|
|
| Sound is not produced from the left or right | ÷ Connect properly referring to "Connections". | 67 |
|
| speaker. |
|
|
|
|
|
|
|
|
| Sound volume is too low. | ÷ Connect properly referring to "Connections". | 67 |
|
| ÷ If the headphones output of a portable component is connected | ||
|
|
| ||
|
|
| to the CD or AUX input connectors, reconnect it to the D.AUDIO | |
|
|
| input connectors. | 6 |
|
|
|
|
|
|
| Sound is too loud and distorted. | ÷ Connect properly referring to "Connections". | 67 |
|
| ÷ If the line output of a desktop component such as a CD player is | ||
|
|
| ||
|
|
| connected to the D.AUDIO input connectors, reconnect it to the | |
|
|
| CD or AUX input connectors. | 6 |
|
|
|
|
|
Speaker protection circuit
The speaker protection circuit is activated when the unit is switched ON while the + and – speaker cords are shorted. When activated, the speaker protection circuit shuts off the audio output to protect both the unit and speakers.
If the speaker cords are shorted, switch the unit OFF, unplug the power cord from the power outlet, and then reconnect the speaker cords properly by removing the
Specifications
[Audio section]
Effective output power during STEREO operation
(1 kHz, 10 % T.H.D., at 8 Ω) | 12 W + 12 W (RMS) |
(1 kHz, 10 % T.H.D., at 6 Ω) | 13 W + 13 W (RMS) |
Rated output power during STEREO operation | |
(63 Hz ~ 12.5 kHz, at 8 Ω) | 10 W + 10 W (DIN) |
(63 Hz ~ 12.5 kHz, at 6 Ω) | 11 W + 11 W (DIN) |
Total harmonic distortion |
|
............................. 0.03 % (AUX IN, 1 kHz, 6 W, 8 Ω) | |
N.B. Circuit |
|
N.B. 1 | +3.0 dB (at 60 Hz) |
N.B. 2 | +5.0 dB (at 70 Hz) |
N.B. 3 | +7.5 dB (at 100 Hz) |
Input (Sensitivity / Impedance) |
|
LINE (CD, AUX) | 250 mV / 22 kΩ |
LINE (D.AUDIO) | 140 mV / 48 kΩ |
Output (Level / Impedance) |
|
SUBWOOFER PREOUT | 1.8 V / 2.9 kΩ |
[General]
Power consumption | 28 W | |
Dimensions |
|
|
Horizontal installation | W | 171 mm |
| H | 67 mm |
| D | 207 mm |
Vertical installation | W | 89 mm |
| H | 182 |
| D | 207 mm |
Weight (net) | 2 kg (4.4 lb) |
Notes : KENWOOD follows a policy of continuous advancements in development. For this reason specifica- tions may be changed without notice.
÷Sufficient performance may not be exhibited at ex- tremely cold locations (where water freezes).
10