“TYPE MIX”:

A total of 6 stations can be assigned to a total of 6 preset buttons regardless of band (FM1, FM2, FM3 MW, SW1, and SW2). You can recall a preset station without switching between bands.

ÎBeep: “KEY BEEP” ➤ “ON”*,“OFF”

Setting the operation check sound (beep sound) ON/OFF.

ÏTDF(Theft Deterrent Faceplate) Attention Alarm: “TDF ALARM” ➤ “ON”,“OFF”* Informs you by sound that you forgot to detach the faceplate when ACC is set to OFF.

ÌBuilt in AUX: “BUILTIN AUX”/“BUILT-IN AUX” ➤

“ON1”*,”ON2”,”OFF”When this is set to ON, AUX source can be selected.

ON1: Outputs the sound of external unit connected to the AUX terminal when switched to AUX source.

ON2: Activates the attenuator function when turning on the power with AUX source selected.

Turn off the attenuator function when listening to output from external unit. This prevents the noise when no external unit is connected to AUX terminal.

OFF: Disables the selection of AUX source.Set to OFF when not using the AUX terminal.

ÓCD READ: “CD READ” ➤ “1”*, ”2” Sets the method for reading CD.

When unable to play special format CD, set this function to “2” to force playing. Note that some music CD may be unplayable even when set to “2”.

In addition, audio files cannot be played when set to “2”. Normally, keep this set to “1”.

1: Automatically distinguishes between audio file disc and music CD when playing disc.

2: Forces playing as music CD.

ÔSwitching Preout: “SWITCH PRE”/“SWITCH PREOUT” ➤ “REAR”*,”SUB-W”

Switches the preout between rear output (“REAR”) and subwoofer output (“SUB-W”).

Speaker Select: “SP SELECT” ➤ “OFF”*, ”5/4”, ”6*9/6”, ”OEM”

Fine-tuning so that the System Q value is optimal when setting the speaker type as follows;

Speaker type

 

Display

OFF

 

 

“SP OFF”

For 5

& 4 in. speaker

 

“SP 5/4”

For 6

& 6x9 in. speaker

 

“SP 6*9/6”
For the OEM speaker

 

“SP OEM”

ÒFirmware Upgrade: “F/W UP xx.xx” ➤ “MEDIA USB”*, ”MEDIA CD”

Upgrades the firmware.Selecting “YES” and then pressing [VOL] knob starts upgrading the firmware.

⁄

•For how to update the firmware, access our web site. http://www.kenwood.com/cs/ce/

<DEMO MODE>

ÚDemo Mode: “DEMO MODE” ➤ “ON”*, ”OFF” Specifies whether to enable demonstration.

<AUDIO CONTROL>

"Subwoofer output: “SUB-W SET”/ “SUBWOOFER SET” ➤ “ON”*, ”OFF”

⁄

•This setting can be made when “SUB-W” is selected for the <Switching Preout> item.

ÆBass Boost: “BASS BOOST” ➤ “LV1”*, ”LV2”, ”OFF” å System Q: “SYSTEM Q” ➤ “NATURAL”*, ”ROCK”,

”POPS”, ”EASY”, ”TOP 40”, ”JAZZ”, ”GAME”, ”USER” Switches between the following preset equalizer curves;

Natural, Rock, Pops, Easy, Top 40, Jazz, Game, User setting

⁄

•“USER”: This appears when Bass level, Middle level, and Treble level are adjusted. When the System Q setting is changed, the Bass, Middle, and Treble set replace the System Q values.

ßBass level adjust: “BASS LEVEL” ➤ “-8” – ”+ 8” ∂ Middle level adjust: “MID LEVEL” ➤ “-8” – ”+ 8” ƒ Treble level adjust: “TRE LEVEL” ➤ “-8” – ”+ 8”

⁄

• ß - ƒ : Source tone memory: Puts the set up value in the memory per source.

©Balance: “BALANCE” ➤ “L 15” – ”R 15” ˙ Fader: “FADER” ➤ “R 15” – ”F 15”

Subwoofer level adjust: “SUB-W LEVEL” ➤ “- 15” - ”+ 15”

Next page 3

English 9