Kenwood KTC-SR901 Accessories, Connecting Wires to Terminals, Installation Procedure, English

Accessories

15

26

3 7

4

Connecting Wires to Terminals

To KENWOOD disc changer / DAB control input / Sirius control input

Control unit

Connection wire	Sirius	SAT	TERR	GND	BATT	3AFUSE
(supplied with the			ANT
Disc changer)	Satellite						Sirius connection wire
	Radio tuner						(Accessory1)
					UNITHEADTO		CHANGERTO
	(Rear side)

2CAUTION

The use of any accessories except for those provided might result in damage to the unit. Make sure only to use the accessories shipped with the unit, as shown above.

(Front side)

Fuse (3A)

To control unit

ANT

FUSE 3A BATT GND TERR SAT

Installation Procedure

1.	To prevent short circuits, remove the key
	from the ignition and disconnect the -
	terminal of the battery.
2.	Install the Sirius antenna and connect the
	antenna wire to the Sirius satellite radio
	tuner.
3.	Connect the Sirius satellite radio tuner and
	the control unit using the provided Sirius

• Some disc changers need conversion

wires for connection. See the section on

"Safety Precautions" for details.

• Do not let unconnected wires or

terminals touch metal on the car or

anything else conducting electricity. To

prevent short circuits, also do not

remove the caps on the ends of the

KENWOOD disc changer control input

NOTE

To connect the Disc changer, consult your Disc changer manual.

Disc changer

	Sirius antenna
Terminal cover	wire
(Accessory5)	Sirius antenna
	(Separated-sale

Ground wire	product)
(Commercially available)
Battery wire
(Commercially available)

	connection wire.
4.	Make the proper input and output wire
	connections for each unit.
5.	Connect the battery wire and ground wire to
	the Sirius satellite radio tuner.
6.	Install the unit in your car.
7.	Reconnect the - terminal of the battery.
8.	Press the reset button on the control unit.

2CAUTION

unconnected wires or the terminals.

• If the fuse blows, first make sure that the

wires have not caused a short circuit, then

replace the old fuse with one with the

same rating.

• Insulate unconnected wires with vinyl

tape or other similar material.

• Take care so that the antenna wire and

other connection wires are not caught by

mobile parts. Otherwise wire

disconnection or other trouble may

Power terminal

Pass battery and ground wires through supplied terminal cover and connect to respective terminals. After completing connections, fasten terminal cover5 over terminal bracket.

Lead terminal	Terminal cover
(Commercially
	(Accessory5)
available)

Car fuse box (Main

fuse)

+ -

Battery

•Do not connect the Sirius control wire while the control unit is turned ON.

•Be sure to press the reset button on the control unit after installation.

•If your car is not prepared for this special connection-system, consult your Kenwood dealer.

•Make sure that all wire connections are securely made by inserting jacks until they lock completely.

result.

• Do not apply too much force on the

antenna wire, other connection wires

and connectors by bending a wire, etc.

Otherwise wire disconnection or other

trouble may result.

• After the unit is installed, check whether

the brake lamps, indicators, wipers, etc.

on the car are working properly.

■If you want to connect KCA-S210A

Control unit	]“N”		Sirius Satellite Radio tuner
			TO	TO
	O N	OFF ON	CHANGER	HEAD UNIT
	PROTOCOL	AUX	AUX
	SWITCH	SWITCH	IN
	TO	TO	TO
	H/U	CHANGER 1	CHANGER 2

Disc changer

KCA-S210A

Connect the KTC-SR901 to the terminal labelled TO CHANGER 2.

NOTE

Set the PROTOCOL selection switch to "N" position.

8 -English English- 9