Kenwood M), TK-2160 TK-2160

TK-2160

6

Assembling

•Installation of battery terminal block and

packing

Install them so that no distortion or deformation occurs.

•Installation of speakers and cushion, and wire

styling of speakers

Install the speakers so that they do not protrude from the

cushion. Perform the wire styling of speakers as shown in a

photograph.

•Attaching the cushion

Attach the cushion as shown in Fig. 1.

Note: Cushion must not cover the screws A,B and C.

DISASSEMBLY FOR REPAIR

Install the cushion

according to the

guide.

•Installation of chassis and cabinet assy

Wire Styling

B

A

C

Fig. 1

Take screw B and

MIC edge as reference

line when sticking.

G13-2018-04

Stick between screw

A and B.

G13-2017-04

G13-2020-04

Do not press this area, top

packing easily deform.

Second, press down the Chassis to the

cabinet assy as shown in the diagram.

Good Condition NG Condition

After mount, packing

should be in this

condition.

Packing deform.

Packing protruded out.

Note:

•Take care that the packing does not protrude from the

chassis or case.

•Replace the protruded or deformed packing with a new one.

First, mount the set to the cabinet assy.

Contents

Main TK-2160 SERVICE MANUAL CONTENTS TK-2160 GENERAL / SYSTEM SET-UP INTRODUCTION SCOPE OF THIS MANUAL ORDERING REPLACEMENT PARTS OPERATING FEATURES 1. Operation Features qq Installing the (Optional) Antenna Installing the Belt Clip OPERATING FEATURES / REALIGNMENT Fig. 1 Programmable Auxiliary Functions 2. How to Enter Each Mode DISASSEMBLY FOR REPAIR // b vv , TK-2160 Assembling Fig. 1 Installation of battery terminal block and packing Installation of speakers and cushion, and wire styling of speakers 1. Frequency Configuration Fig. 2 Receiver section Fig. 1 Frequency configuration 1) Front End (RF AMP) 2) First Mixer 3. PLL Frequency Synthesizer 1) PLL 2) VCO Fig. 6 PLL circuit 3)Unlock Detector Fig. 7 Unlock detector circuit 4. Transmitter System 1)Microphone Amplifier Fig. 8 Microphone amplifier Fig. 9 Drive and final amplifier and APC circuit 3)APC Circuit 4)Encode Signalling 6. Control Circuit 1) Frequency Shift Circuit 5. Power Supply Fig. 10 Frequency shift circuit Fig. 11 Memory circuit CIRCUIT DESCRIPTION / INSTALLATION INSTALLATION 1. Optional Board TX-RX UNIT (X57-6720-10) Component side view TERMINAL FUNCTION CN801 Solder point connection SEMICONDUCTOR DATA Microprocessor : M30622MCA7G7GP (TX-RX UNIT : IC805) Pin function COMPONENTS DESCRIPTION TX-RX UNIT (X57-672X-XX) TK-2160 CAPACITORS CC 45 TH 1H J220 12346 5 1 C TK-2160 TX-RX UNIT (X57-672X-XX) 0-10 : K, M TK-2160 TK-2160 (Y50-578X-XX) Page Page Page Page TK-2160 Page EXPLODED VIEW PACKING Test Equipment Required for Alignment The following parts are required for adjustment 1. Antenna connector adapter 2. Repair Jig (Chassis) 3. Battery Jig (W05-0909-00) Adjustment points TX-RX unit (X57-672) Component side view Foil Side View Fig. 1 Adjustment points Common Section Transmitter Section Page Receiver Section JIHGFEDCBA J72-0895-09 A/2 Foil side PC BOARD TX-RX UNIT (X57-6720-10) Component side view (J72-0895-09) Component side Layer 1 Layer 2 Layer 3 Layer 4 Layer 5 Layer 6 TX-RX UNIT (X57-6720-10) PC BOARD TK-2160 TX-RX UNIT (X57-6720-10) Component side view (J72-0895-09) J72-0895-09 B/2 JIHGFEDCBA PC BOARD TX-RX UNIT (X57-6720-10) Foil side view (J72-0895-09) D14 J72-0895-09 B/2 JKLMNOPQRS PC BOARD TK-2160 TX-RX UNIT (X57-6720-10) Foil side view (J72-0895-09) TX-RX UNIT (X57-6720-10) TK-2160 ABCDE 1 X57-672 1/4 7 2 FGHIJ X57-672 2/4 TK-2160 KLMNO X57-672 3/4 TSRQP 1 :TA75W01FUIC201 :TA31136FNIC401 Note :The components marked with a dot () are parts of layer1. Page BLOCK DIAGRAM LEVEL DIAGRAM TX RX KSC-30 Operating flow chart parts Ref. No. Parts No. Description POWER ON INITIALIZATION INSERT BATTERY Does S terminal connect? Distinguish the kinds of battery SPECIFICATIONS KENWOOD CORPORATION KENWOOD U.S.A. CORPORATION KENWOOD ELECTRONICS CANADA INC. KENWOOD ELECTRONICS DEUTSCHLAND GMBH