Kenwood TK-390 manual Options, Specifications, Applicable MIL-STD

Options

■ KNB-17A	■ KBP-4
Ni-Cd Battery	AA Refillable Battery Pack
(7.2 V, 1500 mAh)	(Holds 12 AA-Size Cells)
■ KNB-17BK
Ni-Cd Battery
Intrinsically Safe
(7.2 V, 1500 mAh)
■ KNB-21N	■ KRA-26
Ni-MH Battery
(7.2 V, 1600 mAh)	VHF Helical Antenna
■ KNB-22N
Ni-MH Battery
(7.2 V, 2100 mAh)
■ KNB-22NC
Ni-MH Battery Intrinsically Safe
(7.2 V, 2100 mAh)	■ KRA-27
■ KNB-44BK	UHF Whip Antenna
Ni-Cd Battery MSHA
(7.2 V, 1500 mAh)

■KSC-19

Regular Charger

Ni-Cd Charger

■KSC-24

Rapid Charger

Dual-chemistry

Ni-Cd/Ni-MH Charger

■KVC-3

Regular Rate

Vehicular Charger

Adapter

■KVC-4

Rapid Rate Vehicular Charger Adapter for (KSC-24) (Charger not included)

■KEP-1

Earphone Coil Cord Kit

■KMC-25

Speaker Micrphone (MIL-SPEC, Noise Canceling)

■KMC-26

Speaker Micrphone

(MIL-SPEC, Noise Canceling

and Antenna Conncetor)

■KBH-8DS

Swivel Belp Loop

with D-Stub Back Plate

Specifications				All accessories and options may not be available in all markets.
				Contact an authorized Kenwood dealer for details and complete list of all accessories and options.
Model	TK-290	TK-390	Model	TK-290	TK-390

GENERAL

Frequency Range

Type 1	136-174 MHz	450-490 MHz
Type 2		470-512 MHz
Type 3		403-430 MHz
Number of Channels	160
Channel Spacing
Wide	25, 30 kHz	25 kHz
Narrow	12.5, 15 kHz	12.5 kHz
	(PLL step: 5/6.25/7.5 kHz)	(PLL step: 5/6.25 kHz)
Battery Voltage	7.5 V DC ± 20 %
Battery Life (5-5-90 duty cycle)
With KNB-17A	10 hours at 5W	10 hours at 4 W
Operating Temperature Range	-22 °F ~ +140 °F (-30 °C ~ +60 °C)
Frequency Stability (-22 °F ~ +140 °F) ±0.00025%		±0.0002%
Antenna Impedance	50 Ω
Channel Frequency Spread
Type 1	38 MHz	40 MHz
Type 2		42 MHz
Type 3		27 MHz
Dimensions (W x H x D), Projections not included
	2-5/16” x 6-3/32” x 1-1/2” (58 x 155 x 38 mm)
Keypad Model	2-5/16” x 6-3/32” x 1-9/16” (58 x 155 x 39.5 mm)
Weight (net)	1.25 lbs. (565g) with antenna and belt hook
FCC ID
Type 1	ALH21893110	ALH21903110
Type 2	–	ALH21903120
Type 3	–	ALH21903130
IC Certification
Type 1	282195345A	282195341A
Type 3	–	282195393A

RECEIVER (Measurements made per RS-316-B)

Sensitivity
(12 dB SINAD)	0.25 µV
(20 dB Quieting)	0.35 µV
Selectivity
Wide	75 dB	73 dB
Narrow	70 dB	68 dB
Intermodulation Distortion
Wide	75 dB	73 dB
Narrow	68 dB	65 dB
Spurious Response	75 dB	73 dB
Audio Output	500 mW with less than 3 % distortion
TRANSMITTER (Measurements made per RS-316-B)
RF Power Output
High	5 W	4 W
Low	1 W	1 W
Spurious Response	70 dB
Type of Emission
Wide	16K0F3E
Narrow	11K0F3E
FM Hum & Noise
Wide	45 dB
Narrow	40 dB
Audio Distortion
Wide/Narrow	Less than 3 %

Kenwood follows a policy of continuous advancement in development.

For this reason specifications may be changed without notice.

FleetSync® is a registered trademark of Kenwood Corporation.

Applicable MIL-STD

Standard	MIL 810C	MIL 810D	MIL 810E	MIL 810F
	Methods/Procedures	Methods/Procedures	Methods/Procedures	Methods/Procedures

Footnotes from Front:

1	Channel Capacity: 16 Channel Groups; 1-160 CH’s per
	group up to 160 Channel Maximum per Radio.
2

Low Pressure	500.1/Procedure I	500.2/Procedure I, II
High Temperature	501.1/Procedure I, II	501.2/Procedure I, II Cat. A1
Low Temperature	502.1/Procedure I	502.2/Procedure I, II Cat. C1
Temperature Shock	503.1/Procedure I	503.2/Procedure I, Cat. A1,C1
Solar Radiation	505.1/Procedure I	505.2/Procedure I
Rain	506.1/Procedure I, II	506.2/Procedure I, II
Humidity	507.1/Procedure I, II	507.2/Procedure II, III
Salt Fog	509.1/Procedure I	509.2/Procedure I
Dust	510.1/Procedure I	510.2/Procedure I
Vibration	514.2/Procedure VIII, X	514.3/Procedure I, Cat. 8
Shock	516.2/Procedure I, II, V	516.3/Procedure I, IV

500.3/Procedure I, II	500.4/Procedure I, II
501.3/Procedure I, II Cat. A1	501.4/Procedure I, II
502.3/Procedure I, II Cat. C1	502.4/Procedure I, II Cat.C1
503.3/Procedure I Cat. A1,C1	503.4/Procedure I, II
505.3/Procedure I	505.4/Procedure I
506.3/Procedure I, II	506.4/Procedure I, III
507.3/Procedure II, III	507.4
509.3/Procedure I	509.4
510.3/Procedure I	510.4/Procedure I, III
514.4/Procedure I, Cat. 8	514.5/Procedure I Cat. 20
516.4/Procedure I, IV	516.5/Procedure I, IV

	Two-Tone Decode (3 sets x 2 pairs each); Operator
	Selectable Tone on Keypad models only (16 QT/DQT code pairs)
3	DTMF encode includes PTT ID, Emergency ANI, Manual
	Encode (keypad models), Auto-Dial (9 numbers). DTMF
	Decode includes primary (individual) & Secondary (group)
	selective call and DBD codes.
4	KPG-38D required: Windows®98/NT/2000/Me/XP compatible.
5	FleetSync® is not compatible with FleetSync® II. PTT ID and
	Emergency Status Encode only.

JQA-QMA1205

ADS#43607 Printed in USA