Kenwood TK-8150 Options, Specifications, Applicable MIL-STD & IP, KMC-9C, KCT-18, KMC-27A, KCT-22

Options

■ KMC-9C	■ KCT-18
Desktop Microphone	Ignition Sense Cable
■ KMC-27A	■ KCT-22
Microphone	Remote Control Cable
(noise-canceling)
	8 feet
■ KMC-27B
Microphone	17 feet
■ KMC-28A
Keypad Microphone	25 feet
(noise-canceling)

■KCT-23

DC Power Cable

Medium Power

Dash (10 feet)

Medium Power Remote (Positive: 23 feet, Negative: 3.3 feet)

■KES-5

External Speaker

■KLF-2

Line Filter

■KPS-10A

Regulated DC

Power Supply

■KPS-15

DC Switching

Power Supply

■KRK-9

Single Control Head Remote Kit

All accessories and options may not be available in all markets. Contact an authorized

Specifications					Kenwood dealer for details and complete list of all accessories and options.
	Model	TK-7150	TK-8150	Model	TK-7150	TK-8150
	GENERAL			RECEIVER (Measurements made per EIA/TIA-603)

Frequency Range
Type1:	136~174MHz	450~500MHz
Number of Channels (Zone)*
Conventional CH:	Max.128 (1 zone x 128ch ~ 128 zones x 1ch)
Trunking ID:	Max. 250/zone (max.32 zones)
Channel Spacing
Wide:	25kHz, 30kHz	25kHz
Narrow:	12.5kHz, 15kHz	12.5kHz
Operating Voltage	13.6V DC±15%
Current Drain
Standby:	0.5A	0.5A
Receive:	2.3A	2.3A
Transmit:	Less than 12A	Less than 13A
Duty Cycle	Transmit: 20%
Operating Temperature Range	-22ºF ~ +140ºF (-30ºC ~ +60ºC)
Frequency Stability	±0.00025%
(-22ºF ~ +140ºF)
Antenna Impedance	50 Ω
Dimensions (W x H x D)	7-1/12” x 2” x 7”
	(180mm x 50mm x 170mm)
Weight (net)	5.9 lbs (2.7kg)
FCC ID	ALH32273110	ALH32283110
Band Spread	38MHz	50MHz

*During simultaneous operation of conventional and LTR® modes. Conventional channel/trunking ID can be programmed up to 512. FleetSync® is a trademark of Kenwood Corporation.

LTR® is a registered trademark of Transcrypt International.

Sensitivity
12dB SINAD:	0.35µV
20dB Quieting:	0.45µV
Selectivity
Wide:	84dB (±30kHz)	80dB (±25kHz)
Narrow:	76dB (±15kHz),	73dB (±12.5kHz)
	76dB (±12.5kHz)
Intermodulation
Wide:	77dB (±30, 60kHz)	79dB (±25, 50kHz)
Narrow:	75dB (±15, 30kHz)	73dB (±12.5, 25kHz)
Spurious Response	85dB
Audio Output
External:	12W (@ 4 Ω 3% distortion)
	13W (@ 4 Ω 5% distortion)
Internal:	3.2W (@ 16 Ω 3% distortion)
	3.5W (@ 16 Ω 5% distortion)
TRANSMITTER (Measurements made per EIA/TIA-603)
RF Output Power	50 to 15 watts	45 to 15 watts
High:	50 watts	45 watts
Low:	15 watts	15 watts
Type of Emission
Wide:	16K0F3E, 20K0F1D
Narrow:	11K0F3E, 11K2F1D
Spurious Response	75dB
FM Hum & Noise
Wide:	48dB
Narrow:	42dB
Microphone Impedance	600 Ω
Audio Distortion	Less than 1% at 1000Hz

Applicable MIL-STD & IP

Kenwood follows a policy of continuous advancement in development. For this reason specifications may be changed without notice.

Standard	MIL 810C	MIL 810D	MIL 810E	MIL 810F
	Methods/Procedures	Methods/Procedures	Methods/Procedures	Methods/Procedures
Low Pressure	500.1/Procedure I	500.2/Procedure I, II	500.3/Procedure I, II	500.4/Procedure I, II
High Temperature	501.1/Procedure I, II	501.2/Procedure I, II Cat. A1	501.3/Procedure I, II Cat. A1	501.4/Procedure I, II
Low Temperature	502.1/Procedure I	502.2/Procedure I, II Cat. C1	502.3/Procedure I, II Cat. C1	502.4/Procedure I, II
Temperature Shock	503.1/Procedure I	503.2/Procedure I Cat. A1, C1	503.3/Procedure I Cat. A1, C1	503.4/Procedure I, II
Solar Radiation	505.1/Procedure I	505.2/Procedure I	505.3/Procedure I	505.4/Procedure I
Rain	506.1/Procedure II	506.2/Procedure II	506.3/Procedure II	506.4/Procedure III
Humidity	507.1/Procedure II	507.2/Procedure II	507.3/Procedure II	507.4
Salt Fog	509.1/Procedure I	509.2/Procedure I	509.3/Procedure I	509.4
Dust	510.1/Procedure I	510.2/Procedure I	510.3/Procedure I	510.4/Procedure I, III
Vibration	514.2/Procedure VIII, X	514.3/Procedure I Cat. 8	514.4/Procedure I Cat. 8	514.5/Procedure I Cat. 20
Shock	516.2/Procedure I, II, III, V	516.3/Procedure I, IV, V	516.4/Procedure I, IV, V	516.5/Procedure I, IV, V

footnotes from Front:

1KRK-9, KCT-22M/M2/M3, KCT-23M/M3 remote control options required.

26-Pin Accessory Connector for external speaker, PA Output & ignition sense input.

3KCT-18 ignition sense cable option required; plugs into mobile 6-pin jack ignition sense input.

4Built-in PA/HA outputs (no option board required); Horn Alert operates for 2-Tone or DTMF selective call decode only.

5Short Text Messages are radio stored & LCD displayed; Long Text Messages require a KDS-100 and KCT-40.

6FleetSync® GPS features require an internal GPS board or externally wired GPS receiver with NMEA TTL level serial data output to the internal COM 1 or 2 set to "GPS".

JQA-QMA1205

ADS#26608 Printed in USA