Kenwood TS-480HX, TS-480SAT USING TH-D7A AS A COMMANDER, CONTROL OPERATION

13 OPERATOR CONVENIENCES

yeKciM noitcnuF

1FFOrewoP

2FFO/NOeviecerycneuqerfFH

3hctiwsedomnoitaludoM

4FFO/NOTIR

5FFO/NOTIX

6raelctesffoTIXrotesffoTIR

7FFO/NOycneuqerf-tilpS

8OFVotyromeMmorfrefsnarT

9hctiwsBOFV/AOFV:edomOFVnI

egnahcoN:edomllaceRyromeMnI

0eveirtersgnittestnerruC

)reviecsnartFHmorf(

BhctiwsedomllaceRyromeM/OFV

CesaercniycneuqerftesffoTIR/TIX

DesaercedycneuqerftesffoTIR/TIX

:edomWCro,BSU,BSLnI

hctiwszHk1/zH01

hctiwszHk01/zHk1:edomMAroMFnI

NOyrtneycneuqerF:edomOFVnI

rebmunlennahC:edomllaceRyromeMnI

NOyrtne

1“FS” appears when you select 1 kHz step (LSB/ USB/ CW) or 10 kHz

step (FM/ AM).

2After pressing Mic [#], press Mic [0] to [9] to enter a frequency or

memory channel number.

When Mic [0] is pressed, the Commander shows the

current settings of the HF transceiver:

eyr

qHF frequency

wVFO: A, VFO: B,

MR: 00 ~ 99 (memory channel number)

eRIT, XIT

rOFF, –9.99 ~ +9.99

tLSB, USB, CW, FM, or AM

ySPLIT–A: VFO A is used for transmitting.

SPLIT–B: VFO B is used for transmitting.

SPLIT–M: A memory channel is used for transmitting.

u“FS” appears when Mic [] is pressed.

Note:

◆

After pressing

[MENU]

, you can access only Menu 4–4.

◆

The Transporter will transmit its call sign in Morse code every

10 minutes, using the 144 MHz band.

◆

The APO timer will not operate on the transceiver while the

Transporter is ON.

USING TH-D7A AS A COMMANDER

To use a TH-D7A transceiver as a “Commander” (an

external remote control unit), follow the steps below.

Basically, it is the same as using a TM-D700A as a

“Commander” (described on the previous page).

TS-480 + TH-D7A/ TM-D700A (Transporter) Setup:

1Configure the TH-D7A or TM-D700A as a

“Transporter” and connect all the necessary

cables to the TS-480 transceiver.

2Select a frequency (HF/ 50 MHz band) on the

TS-480 transceiver.

3On the TS-480, press [MENU/ F.LOCK], then turn

the MULTI control to access Menu No. 56.

4Select the same communication parameters that

you selected for the TH-D7A or TM-D700A

transceiver.

5Press [MENU/ F.LOCK] to complete.

6Start the Transporter mode on the TH-D7A or

TM-D700A transceiver.

TH-D7A (Commander) Setup:

1Access Menu 4–1 to enter the same callsign that

you entered for the Commander (ex: WD6DJY).

2Access Menu 4–2 to enter the same callsign that

you entered for the Transporter (ex: WD6DJY-1).

3Access Menu 4–3 to select the same CTCSS tone

frequency that you selected for the Transporter.

4Set the same frequencies that you selected for the

“Transporter” for the VHF and UHF bands.

Note:

Refer to Chapter 19, Sky Command II, of the TH-D7A

instruction manual for details on how to enter the callsign and CTCSS

tone frequency.

CONTROL OPERATION

First, switch the TS-480 and TH-D7A or TM-D700A

transceivers (Transporter) ON. Configure the

TH-D7A or TM-D700A to enter the “Transporter”

mode.

Then, access Menu 4–4 on the TH-D7A and select

“COMMANDER”. “PUSH [0] KEY TO START

COMMANDER!!” appears.

Press [0] on the TH-D7A to start Sky Command II

mode.

When in Sky Command II mode, the keys of the

TH-D7A (Commander) will function as described

below. Only [LAMP], [MONI], and the VOL control

functions will not change.

Each time you press the desired key, the Commander

will automatically enter Transmission mode and send

the corresponding control command to the

Transporter.