FIXTURE

ARTEFACTO

threaded pipe tubo roscado

hexnut

tuerca hexagonal

mounting STRAP PLANCHA PARA MONTAR

Bulb bombilla

1)Turn off power.

IMPORTANT: Before you start, NEVER attempt any work without shutting off the electricity until the work is done.

a)Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.

b)Unscrew the fuse(s), or switch “OFF” the circuit breaker switch(s), that control the power to the fixture or room that you are working on.

c)Place the wall switch in the “OFF” position. If the fixture to be replaced has a switch or pull chain, place those in the “OFF” position.

2)Attach mounting strap to outlet box. (Screws not provided.)

3)Thread hexnut onto threaded pipe so that 5 theads are exposed above hexnut. Thread that end of the threaded pipe into mounting strap and tighten hexnut against mounting strap.

4)Grounding instructions: (See Illus. A or B).

A)On fixtures where mounting strap is provided with a hole and two raised dimples. Wrap ground wire from outlet box around green ground screw, and thread into hole.

B)On fixtures where a cupped washer is provided. Attach ground wire from outlet box under cupped washer and green ground screw, and thread into mounting strap.

If fixture is provided with ground wire. Connect fixture ground wire to outlet box ground wire with wire connector (not provided.) after following the above steps. Never connect ground wire to black or white power supply wires.

A

 

 

B

 

 

wIre ConneCTor

 

ouTleT Box

(noT proVIDeD)

 

 

 

fIxTure

GrounD

 

 

 

 

GrounD

 

 

 

 

 

 

fIxTure

 

 

 

 

GrounD

 

 

 

 

DIMpleS

ouTleT Box

 

 

 

GrounD

 

 

 

 

 

Green GrounD

 

Green GrounD

CuppeD

 

SCrew

wASHer

SCrew

 

 

 

 

5)Make wire connections (connectors not provided). Reference chart below for correct connections and wire accordingly.

Connect Black or

Connect

Red Supply Wire to:

White Supply Wire to:

 

 

 

Black

White

 

 

 

*Parallel cord (round & smooth)

*Parallel cord (square & ridged)

 

 

Clear, Brown, Gold or Black

Clear, Brown, Gold or Black

without tracer

with tracer

 

 

 

Insulated wire (other than green)

Insulated wire (other than green)

with copper conductor

with silver conductor

 

 

 

*Note: When parallel wires (SPT I & SPT II)

 

are used. The neutral wire is square shaped

 

or ridged and the other wire will be round in

 

shape or smooth (see illus.)

Neutral Wire

 

6)Push fixture to wall, carefully passing threaded pipe through hole.

7)Tighten fixture to wall with threaded cap.

8)Push bulb into socket. Turn bulb to the right slightly to lock bulb in place.

INSTRUCTIONS FOR MOUNTING FIXTURE OUTDOORS AND/OR IN WET LOCATIONS.

9)Mounting surface should be clean, dry, flat and 1/4” larger that the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.

10)With silicone caulking compound, caulk completely around where back of canopy meets the wall surface to prevent water from seeping into outlet box.

threaded CAP tAPA roscado

1)Apague la alimentación eléctrica.

IMPORTANTE: Antes de comenzar, NUNCA trate de trabajar sin antes desconectar la corriente hasta que el trabajo se termine.

a)Vaya a la caja principal de fusibles, o interruptor o caja de circuitos de su casa. Coloque el interruptor de la corriente principal en posición de apagado “OFF”.

b)Desatornille el (los) fusible (s), o coloque el interruptor o interruptores del breaker en posición de apagado “OFF”, que controla (n) la corriente hacia el artefacto o habitación donde está trabajando.

c)Coloque el interruptor de pared en posición de apagado “OFF”. Si el artefacto que se va a reemplazar tiene un interruptor o cadena que se jala, colóquelos en la posición de apagado “OFF”.

2)Sujete la plancha para montar a la caja de conexión. (No se proveen los tornillos.)

3)Atornille la tuerca hexagonal en el tubo roscado de manera que 5 hilos de rosca estén expuestos arriba de la tuerca hexagonal. Atornille el extremo del tubo roscado en la plancha para montaje y apriete la tuerca hexagonal contra la plancha para montaje.

4)Instrucciones de conexión a tierra solamente para los Estados Unidos. (Vea la ilustracion A o B).

A)En las lámparas que tienen el fleje, de montaje con un agujero y dos hoyuelos realzados. Enrollar el alambre a tierra de la caja tomacorriente alrededor del tornillo verde y pasarlo por el aquiero.

B)En las lámparas con una arandela acopada. Fijar el alambre a tierra de la caja tomacorriente del ajo de la arandela acoada y tornillo verde, y paser

por el fleje de montaje.

Si la lámpara viene con alambre a tierra. Conecter el alambre a tierra de la lámpara al alambre a tierra de la caja tomacorriente con un conector de alambres. (No incluido) Espués de seguir los pasos anteriores. Nunca conectar el alambra a tierra a los alambres eléctros negro o blanco.

A

 

B

 

ConeCTor De AlAMBre

 

TIerrA De lA

(no Se proVee)

 

 

TIerrA

CAJA De SAlIDA

 

TIerrA

ArTefACTo

 

 

 

 

ArTefACTo

 

 

TIerrA De lA

 

 

CAJA De SAlIDA

 

 

DepreSIoneS

 

TornIllo De TIerrA,

TornIllo De TIerrA,

ArAnDelA

VerDe

VerDe

ConCAVA

 

5)Haga les conexiones de los alambres (no se proveen los connectores.) La tabla de referencia de abajo indica las conexiones correctas y los alambres correspondientes.

Conectar el alambre de

Conectar el alambre de

suministro negro o rojo al

suministro blanco al

 

 

Negro

Blanco

 

 

*Cordon paralelo (redondo y liso)

*Cordon paralelo (cuadrado y estriado)

 

 

Claro, marrón, amarillio o negro

Claro, marrón, amarillio o negro

sin hebra identificadora

con hebra identificadora

 

 

Alambre aislado (diferente del verde)

Alambre aislado (diferente del

con conductor de cobre

verde) con conductor de plata

 

 

*Nota: Cuando se utiliza alambre paralelo

 

(SPT I y SPT II). El alambre neutro es de forma

 

cuadrada o estriada y el otro alambre será de

 

forma redonda o lisa. (Vea la ilustracíón).

Hilo Neutral

 

6)Empuje el artefacto a la pared pasando cuidadosamente el tubo roscado a través del agujero.

7)Sujete la unidad contra la pared apretándola con la tapa roscada.

8)Empuje la bombilla en el casquillo. Gire la bombilla ligeramente a la derecha para trabar la bombilla en el lugar.

INSTRUCCIONES PARA EL MONTAJE DEL ARTEFACTO AL AIRE LIBRE Y/O EN UN LUGAR MOJADO.

9)La superficie de montaje debe estar limpia, seca, ser plana y 1/4” más grande que el esdudete en todos los bordes. Cualquier espacio libre entre la superficie de montaje y el escudete que exceda de 3/16” debe corregirse según se requiera.

10)Calafatee totalmente con compuesto de calafatear de silicona alrededor donde el escudete sienta en la superficie de la pared para impedir la entrada de agua en la caja de conexiones

Date Issued: 6/24/11

IS-10962-US

Page 1
Image 1
Kichler Lighting 10962CV manual Fixture, Artefacto, Threaded CAP tAPA roscado, Date Issued 6/24/11 IS-10962-US

10962CV specifications

Kichler Lighting has long been a trusted name in innovative lighting solutions, and the Kichler Lighting 10962CV is no exception. This striking outdoor wall light combines aesthetic elegance with practical functionality, making it a popular choice for homeowners looking to enhance the beauty of their outdoor spaces.

One of the main features of the Kichler 10962CV is its contemporary design. The fixture boasts a sleek, modern silhouette that can blend seamlessly with various architectural styles. Its understated elegance makes it suitable for a range of exterior applications, from enhancing patios to illuminating entryways. Available in a rich Cavern Bronze finish, the light adds a touch of sophistication while maintaining a natural, earthy tone that complements outdoor settings.

The Kichler 10962CV is equipped with advanced LED technology, making it an energy-efficient choice for outdoor lighting. This fixture delivers a bright, warm light, providing excellent illumination while consuming less power than traditional incandescent options. The long-lasting LED bulbs also mean lower maintenance costs over time, as they don't need frequent replacement.

In addition to its efficiency, the Kichler 10962CV is designed for durability. It is constructed from high-quality materials that are resistant to rust and corrosion, ensuring it can withstand various weather conditions. This resilience makes it suitable for use in both residential and commercial outdoor environments.

Installation of the Kichler 10962CV is straightforward, allowing homeowners to quickly enhance their outdoor lighting without the need for professional assistance. The fixture is designed to fit standard junction boxes, making it compatible with most existing outdoor wiring systems.

Another notable characteristic of the Kichler 10962CV is its versatility. It can be used in multiple outdoor settings, from illuminating pathways and driveways to accentuating architectural features. With its clean lines and stylish finish, this fixture can transform any outdoor area into a beautifully lit space.

In summary, the Kichler Lighting 10962CV is a perfect blend of style, efficiency, and durability. With its modern design, advanced LED technology, easy installation, and versatility, it is an ideal choice for those looking to enhance their outdoor spaces while enjoying the benefits of energy savings and longevity.