Installation

Tweeter Mounting

If custom door mounting locations for the KS-Series Tweeters are desired, be careful to avoid interference from the window and door lock mechanisms. The first step is to find a location on the door panel that will accept the dimensions of the speaker. Then remove the door panel from the door, and check for operational clearance of the window. Cycle the window all the way down and up. If metal must be cut to mount the speakers, avoid structural metal and braces. An optional reinforcing panel (thin piece of wood or Medium Density Fiberboard) may be necessary if the door panel cannot support the mounting of the speaker. Mount the speaker to the door panel and door body as outlined in Figure 1.

If the factory door speaker wiring is not available, it will be necessary to run the supplied wire through the door jamb. The speaker wire should be kept away from sharp edges and avoid the possibility of getting pinched by the door. An existing grommet in the door jamb is the ideal place to run the speaker wire. If the factory hole and grommet do not exist or are inaccessible, you must drill a hole to run the speaker wire through the door jam. Be careful not to drill into other wiring or existing door mechanisms. Any time a wire is run through a hole, it is necessary to insert a rubber or plastic grommet to protect the wire from damage as outlined in Figure 2.

Installation

The tweeter can be mounted one of three ways: flush, surface and angled mounting. For flush mounting applications, please refer to the illustration in Figure 3 and 4. Mount the tweeter as high up on the door and as far forward as possible without interference from the dashboard. Choose a flat location on the door with space behind the panel to allow room for the mounting nut.

After checking the clearances, cut the appropriate mounting hole diameter in the door panel. Place the

Figure 1

 

Figure 2

(Optional)

 

Stagger Holes

 

 

 

 

For Wiring &

 

 

Use Grommets

 

Door Panel

(When Factory Holes and

 

Grommets are not Available)

 

 

To Crossover

Kick Panel

mounting nut behind the door panel. Feed the wire through the door and body panels. Mount the tweeter by screwing the tweeter onto the mounting nut.

For surface mounting applications, remove the tweeter face plate by screwing it off and install the supplied smaller face plate. Use the surface mount cup as a template and drill a 7/64” (2.8 mm) hole in the center for attaching the cup to the door and a 5/16”

(7.9 mm) hole for the wires. A #8 flathead sheet metal screw is supplied to attach the surface mount cup to the door panel. Position the tweeter over the surface mount cup and press it into position.

For angled mounting applications use the back angle ring behind the panel and the front angle ring in front of the panel, and place the tweeter through the front angle ring and then into the panel. Next place the back angle ring over the tweeter and line up the narrow part of the front angle ring for proper operation. Attach the longer tweeter mounting nut but do not completely tighten. Rotate

KS-Series Tweeters

5

Page 4 Page 6
Page 5
Image 5
Kicker KS13, KS25, KS20 manual Installation, Tweeter Mounting
Page 4 Page 6

KS20, KS25, KS13 specifications

Kicker has long been synonymous with high-quality audio products, and their KS series is no exception. The KS13, KS25, and KS20 are standout speakers designed to enhance your listening experience, whether in your car, at home, or on the go. Each of these models comes with distinct features and technologies that cater to the varying needs of audio enthusiasts.

The Kicker KS13 is a compact 3-inch speaker that excels in delivering quality sound in tight spaces. Its oversized voice coil ensures that it can handle high power levels with ease, while the polypropylene cone provides durability and longevity. The KS13 also incorporates a robust crossover network, which helps to provide a balanced sound profile and allows for better separation of frequencies. The speaker is designed for both coaxial and component setups, making it versatile for any custom installation.

Moving on to the Kicker KS25, this 5.25-inch speaker brings a fuller sound to the table. Packed with features like a polypropylene woofer and a butyl rubber surround, the KS25 is built to deliver deep bass while maintaining clear highs. Its 1-inch silk dome tweeter provides smooth high-frequency reproduction, making it suitable for a wide variety of music genres. The KS25 also boasts a powerful motor structure that enhances overall efficiency, ensuring that you get the most out of your audio system without significant power drain.

The KS20 takes things up a notch with a more robust 6.5-inch design. This model is engineered for those who desire a richer, more immersive sound experience. The KS20 features a weather-resistant design, making it suitable for outdoor use. Both the woofer and tweeter are optimized to work seamlessly together, providing an impressive frequency response that enhances vocal clarity and instrument detail. The speaker also comes with an advanced crossover system to reduce distortion and ensure a cohesive sound profile across a wide range of frequencies.

All three models in the Kicker KS series share a commitment to innovation and performance. They are designed with the consumer in mind, incorporating advanced materials and engineering techniques that set them apart from the competition. With their stylish aesthetics and powerful performance capabilities, the KS13, KS25, and KS20 make excellent choices for anyone looking to elevate their audio experience. Whether you're a casual listener or a serious audiophile, Kicker has a solution that will suit your needs perfectly.
Top Page Image Contents