Kidde 1296 Architectural and Engineering Specifications, Installation of Smoke Alarm, Model

UTHA / UTGT Compliant

Smoke Alarm

Architectural and Engineering Specifications

The smoke alarm shall be Kidde Unit 1296E or approved equal. It shall be powered by a 120VAC, 60Hz source along with a 9V battery backup. The unit shall incorporate an ionization sensor with nominal sensitivity of 0.84%/ft. The temperature operation range shall be between 40˚F and 100˚F (4˚C and 38˚C) and the humidity operation range shall be 5% - 95% relative humidity.

The smoke alarm can be installed on any standard single gang electrical box, up to a 4” octagon junction box. The electrical connection (to the alarm) shall be made with a plug-in connector. A maximum of 24 Kidde devices can be interconnected in a multiple station arrangement. The interconnect system must not exceed the NFPA (National Fire Protection Association) limit of 18 initiating devices (Smoke, heat, CO, etc) interconnected, it is still possible to interconnect 6 strobe lights and or relay modules. The alarm shall provide optional tamper resistance that deters removal of the unit from the wall or ceiling.

The unit shall include a piezoelectric horn that is rated at 85dB at 10ft. The unit shall incorporate 2 LED’s. A green LED will be constantly “ON” when AC power is present. A red LED will flash once approximately every

30-40 seconds to indicate that the smoke alarm is operating properly and will flash rapidly when the unit is alarming and will remain so until the air is cleared. The red LED will be on while test B button is being pressed and will illuminate for about 1.5 seconds every 16 seconds to indicate the memory condition until unit is reset.

The unit shall incorporate two test buttons. Test button A shall test all the electronic circuitry, horn, and battery. Test button B shall test the alarms senor sensitivity.

The unit shall at a minimum meet the requirements of UL217, NFPA72, (chapter 10 & 11 2002 edition) The State of California Fire Marshall, NFPA101 (One and two family dwellings, Federal Housing Authority (FHA), Housing and Urban Development (HUD).

Installation of Smoke Alarm

The smoke alarm should be installed to comply with all local codes having jurisdic- tion in your area, Article 760 of the National Electric Code, and NFPA 72. Make certain all alarms are wired to a single, continuous (non-switched) power line, which is not protected by a ground fault interrupter. A maximum of 1000 ft. of wire can be used in the interconnect system.

FUSE OR CIRCUIT BREAKER

L

N

BLACK	RED
WHITE

First	Additional
Alarm	Alarms

Model 1296

Technical Specifications

Model Number:		1296
UPC:		0-47871-05127-4
Power Source:		120VAC, 60HZ, 9V battery backup
Sensor:		Ionization
Audio Alarm:		85dB at 10ft
Temperature Range:		40˚F (4.4˚C) to 100˚F (37.8˚C)
Humidity Range:		5%-95% relative humidity (RH)
Size:		5.6” in diameter x 1.55” depth
Weight:		.5lb
Interconnects:		Up to 24 Kidde devices
LED:		Green, AC power present
		Red, alarm mode
Warranty:		5 year limited
	5.6"		1.55"

Ordering Information

Gift Box UPC:	0-47871-05127-4
Part			Dimensions		Case/	Layers/	Skid
Number	I 2 of 5	Pack Quantity	(w x d x h inches)	Weight	Skid	Skid	Weight
21005186**	N/A	Individual	5.75 x 1.75 x 5.75	.5lb	N/A	N/A	N/A
21005127	100 47871 05127 1	Master (6 units)	6 x 11.5 x 6	3.5lbs	162	6	567lbs
**Not for sale by individual unit
						1	6
						UNIT	MASTER PACK

Distributed by:

1394 South Third Street, Mebane NC 27302

1-800-880-6788 • www.kiddeus.com